665712
11
Zoom out
Zoom in
Previous page
1/64
Next page
11/64
Adjustable Arc Force
The Arc Force is adjustable (between 0 and 100%) within the limit of 160A.
1- Press and hold the “Arc Force” button
2- Select the required setting
TIG WELDING
Select Starting Function
Select LIFT or HF function.
TIG LIFT : Contact start (for environments sensitive to HF disturbances)
1- Touch the work-piece with the electrode
2- Press the trigger on the torch
3- Lift the electrode.
HF TIG : High Frequency start without contact
Trigger behaviour
The TIG 207FV/208 automatically detects the type of torch that is connected. (Suitable for various kinds of
TIG torches: trigger, simple command, dual command, dual potentiometer)
2T mode
1- Press and hold trigger : pre-gas, up slope, welding
2- Release trigger : down slope, post-gas
NB: For dual control torches and dual potentiometer command “up / warm current” and potentiometer
active, command "low / cold current" inactive
4T mode
1- Press trigger : Pre-gas, followed by start. In order to make
positioning the electrode easier, a low current is supplied acting like a
light beam. (=Adjust Ideal Position)
2- Release trigger : Up-slope until the displayed instruction, welding
3- Press trigger : Down-slope to low current (allows good closure of
the crater)
4- Release trigger : stops the current and post-gas.
Nb: For dual controls torches and dual potentiometer command “up / warm current” and potentiometer
active, command "low / cold current" inactive
4T Log mode
This mode is the same as the 4T mode but when in welding phase, a short tap on the trigger allows a shift
to a previously set cold current (20% at 70% of hot welding current).
1- Press trigger : pre-gas, followed by starting. In order to make the
electrode positionning easier, a low current is supplied, acting like a
light beam. (=Adjust Ideal Position)
2- Release trigger : elevation of the current to the "hot" welding
current (displayed instruction)
short impulse : shift to cold current (%I)
short impulse : back to the "hot" current.
3- Press trigger : down slope to low current (for a good closure of the
crater)
4- Release trigger : stops the current and post-gas.
To repeat
as you wish
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys TIG 207 AC-DC HF FV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys TIG 207 AC-DC HF FV in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info