Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment. During set up,
the operator must ensure that the machine is not connected to the mains.
Risk of harm caused by mobile elements !
The wire feeders contain moving parts that may catch hands, hair, clothes or tools which can lead to injuries! Take extra care.
• Do not touch pivoting or mobile parts or parts used for the feeding parts !
• Make sure that all panels remain closed when in use !
GENERAL DESCRIPTION
NOMADFEED is a mobile MIG/MAG/Open-Arc wire feed case. The plastic casing makes it naturally electrically insulated and it also has the IP23 pro-
tection rating meaning it is protected against water projections and external elements. It powers itself by using the voltage available on the welding
circuit. This voltage can come from a current source (CC), a voltage source (CV), an alternative signal, a positive direct signal or negative direct signal.
NOMADFEED pilots the arrival of the gas, the welding current and wire feeding. On the NOMAFEED 425-4, the welding current, welding voltage, wire
feeding speed and power supply voltage are displayed.
The powerful wire feed motor assembly has 4 drive rolls and is suitable for standard and cored/ux wire up to 2.4mm thick..
EQUIPMENT DESCRIPTION (FIG-1)
1-Wire feeder motor9-Protection fuse
2-Earth clamp connection cable10-Gas purge button (only on Nomadfeed 425-4)
3-2 times / 4 times switch11-Wire feed button
4-Main switch12-Selection of «Soft Start» mode (only on Nomadfeed 425-4)
5-Wire speed potentiometer13-Selection of CC or CV mode
6-Protection "feet"14-Arrival of gas
7-Control panel15-Power supply cable
8-Reel support
MAN MACHINE INTERFACE (MMI) (FIG 2)
Nomadfeed 330-4Nomadfeed 425-4
L05 - Overheating indicator
L06 - Overvoltage indicator
L07 - Voltage at torch indicator
L10 - Voltage in the equipment indicator (machine is powered
up)
L01 - Wire speed display indicator
L02 - Welding current display indicator
L03 - Welding voltage display indicator
L04 - Power supply voltage display indicator
L05 - Overheating indicator
L06 - Overvoltage indicator
L07 - Voltage at torch indicator
L08 - 3 digits welding or power supply voltage
L09 - 3 digits welding current or feeding speed diplay
CONNECTIONS AND RECOMMENDATIONS
Make sure the welding generator is switched off when connecting or disconnecting the wire feeder.
The unit is powered by connecting the power cable in the case to a welding generator. You must choose the polarity based on the type of wire used.
The welding cable potential will be the same as the welding torch.
Connect the second polarity of the generator to the piece to weld.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Gys NOMADFEED 425-4 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Gys NOMADFEED 425-4 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.
The manual is 4,04 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
