665744
13
Zoom out
Zoom in
Previous page
1/71
Next page
13
MULTIPEARL 200.2 / 200.4 XL / 201.4
EN
DESCRIPTION
This manual contains safety and operating instructions. Read it carefully before using the device for the rst time and retain for future
reference.
MULTIPEARL 200.2 / 200.4 XL / 201.4 are multiprocess welding machines (MMA, TIG & MIG/MAG) with Synergy Technology for
MIG/MAG. They are suitable for welding steel, stainless steel and aluminium. Easy and quick to set up thanks to the Synergic mode.
POWER SUPPLY
The input current (I1eff) for use at maximum output is indicated on the device. Check that the power supply and its protection (fuse
and/or circuit breaker) are compatible with the current required. The device must be placed in such way that the power socket is
always accessible.
Do not use extension lead with a section lower than 2.5 mm². MULTIPEARL 200.2 / 200.4 XL / 201.4 are delivered with a 16A plug
CEE7-7 type. It must be connected to a power supply with earth between 110V and 230V 50/60Hz protected with a 16A circuit-
breaker (32A in 110V).
- If the voltage is < 85V or > 265V, the device won't turn on.
- Protected against overvoltage MULTIPEARL 200.2 / 200.4 XL / 201.4 will automatically stop in case of overvoltage.
MACHINE DESCRIPTION (FIG I)
1 - Control panel
2 - Positive Dinze connector
3 - Negative Dinze connector
4 - Polarity reversal cable
5 - Euro torch connector
6 - Reel adaptor 100/200mm (200.2) or 200/300mm (200.4 XL
/ 201.4)
7 - Power lead (2.10 m)
8 - Quick release gas connector.
9 - ON/OFF switch
SWITCHING ON
The ON/OFF switch is located at the back of the machine. Turn the switch on the "I" position to start the generator. This switch
must not be turned off (to "O") while welding.
MIG MANUAL - FIG III
• Selecting MIG manual mode Keep button 2 pushed and at the same
time turn the upper knob until the display
shows MIG Manual. Release button 2 to
validate this selection
+
MANUAL
• Wire speed adjustment Turn the upper knob to adjust the wire
speed.
• Arc voltage adjustment Turn the lower knob to adjust the arc
voltage.
• Setting management torch in SPOT and
DELAY mode
• Keep button 3 pushed to select normal
mode.
• Keep pressing button 3 and at the same
time turn the upper knob to select SPOT
mode and to congure it. Adjustable
between 0.5 to 5 sec.
In the same way turn the lower knob to
congure the DELAY mode. Adjustable
between 0 to 5 sec."
+
MIG SYNERGIC - FIG III
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gys MULTIPEARL 200-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gys MULTIPEARL 200-2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info