624539

Gude W 520-5 T Manual

49
Zoom out
Zoom in
Previous page
1/68
Next page
GB
• If the stock is not split up immediately, hold the cylinder on. Pull the stock sliding device back and try
again. A small stock may be difficult to work if it is knaggy and fibrous. With wood of regular fibrous
composition, it will not be difficult to work stock of larger diameter. If the wood is very hard, the stock
should be left for machine working to avoid damage.
• Repeat the operation with pre-cut shorter pieces of wood.
• With the work completed, the machine should be unplugged. Do not unplug pulling the cable.
Notice: The motor metal part is cold during the operation. In several working hours, the pump may get
very hot. It is not harmful to the machine as it may work again after cooling down. It is very important not
to overheat the oil and the pump when working large or hard stock.
Troubles – Causes – Troubleshooting
CAUTION: ALWAYS CHECK THE THERMAL FUSE FIRST!
Trouble Cause Troubleshooting
The block will not rend
1. Wrong positioning .
2. The stock size not within permissible limits
or the wood too hard for the machine
capacity.
3. The blade will not cut
4. Oil too cold
5. Oil leakage
6. Hydraulic pressure too low.
1. Position the block
2. Cut the block shorter, adjust
3. Sharpen the blade check it for sharp edges or
recesses formation, or reface if necessary
4. Warm up at idling. .
5. Find the place of leakage and seal it.
6. Discard the wood.
Jerky run or strong
vibrations of the piston
rod
Air in the circuit
Check the oil level, replenish, if necessary.
Inquire at the dealer’s if necessary.
Oil leakage at the
piston rod or outer
parts.
1. Oil leaking from the oil tank.
1. Worn gasket
Before positioning, check the bleed screw fit
Replace the gasket
The block to be split
has jammed
1. The block too knaggy 1. Retract the sliding worktable completely to release
the control .
Inspections and Maintenance
Prior to any maintenance, the machine should be put out of operation and unplugged, if it is an electric
drive machine. The maintenance not described in this manual should be done by skilled personnel only
as the operator is not ready to handle the situations that may arise. Scheduled maintenance and
replacement of parts should be done by special personnel only. .
The manufacturer should not be held liable for any personal and material losses due to a failure to
observe these rules.
Wechsel des Hydrauliköls
HLP 46 (# 42004)oil is recommenced for the hydraulic cylinder
Or hydraulic oils of similar viscosity
• Make sure that the motor bearer is completely retracted.
• Remove the screwed closure (Fig. A).
• Put a collecting tub of approximate volume of 4 litres under the
cleaving machine.
• Tilt the machine for the oil to pour out (Fig. B).
• Tilt the cleaving machine in the other direction (Fig.3) and fill 2.6 l of
oil in the filler hole
• Use the oil level indicator – previously cleaned – and check the oil
level. It should be between the two marks on the indicator.
• Clean the closure and the screw and close again.
NOTICE:
The used oil should be disposed of in conformity with the locally
effective legal regulations.
Check the oil level using an oil level indicator on a regular basis.
49
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude W 520-5 T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude W 520-5 T in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info