624539

Gude W 520-5 T Manual

48
Zoom out
Zoom in
Previous page
1/68
Next page
GB
Use only on a power connection equipped with a faulty current switch (FI). In cold weather, have the
machine warmed up at idling until the oil gets warmed up (or, have several idling runs).
Motor overloading or electric installation different from the purpose will result in protective fuse blow up or a
response of the faulty current protection switch FI: that being the case, a qualified electrician should be
called.
Stock Size
The stock diameter is shown as an example. It may be difficult to
cleave/split a small stock, if it is knaggy. Notice: If a stock is not to be
chopped up immediately, it is important that the cleaving pressure is
not applied for too long. That would cause fast overheating of the oil
under pressure and consequent damages to the pump.
Operator Safety Instructions
• Do not use the machine until you have read the instruction manual carefully.
• Observe any safety instructions included In the manual.
• Be responsible to the others
• The wood should be split along the grain only.
• There is a risk of jamming the knaggy material while being split. Remember that the wood is under
considerable pressure when being taken out and may nip your finger in the gap.
• Check to see that all iron parts that are hopping and could damage the machine while the job is being
done have been removed from the piece to be worked. The ends of the stems have to be cut square.
Any knags have to be cut off completely. .
• Never cleave the stocks, the size of which is beyond the limits determined, it could cause injuries and
damage to the machine.
• The wood should be cleaved along the grain. Never put a stock across the machine and never work it in
such a position; it could cause injuries and damage to the machine.
• In no case cleave two stocks at a time. One of them could rebound and hit the operator!
• If the stock slides down of the knife, pull the stock thrust device back and turn the stock by 180°.
• Do not operate the wood cleaving machine at full for more than 10 - 15 seconds, e.g. holding the
cylinder pressed down or cleaving hard material. That would result in fast overheating the oil and
causing damage to the machine subsequently. It is recommended to turn the stock by 180° and to try to
work it in the position. If it is not possible to split up the stock, discard it, to avoid damage to the
machine.
• Given unfavorable conditions in the power supply the equipment may cause the voltage to drop
temporarily.
• If the supply impedance “Z” at the connection point to the public power supply exceeds 0,233 Ω
EN
61000-3-11
it may be necessary to take further measures before the equipment can be used as intended
from this power supply.
• If necessary, you can ask your local electricity supply company for the impedance value.
Step-by-Step Instructions
• Connect the motor wood-cleaving machine to the power.
• Connecting the power cable, mind that it is not let via a telescopic bearer or close to the cleaving knife.
Also, avoid any places where a risk of damage or disruption exists.
• Place the stock on the bearer. The guides will assist you in keeping the stock at the centre of the knife. If
the stock does not fit tightly, it should be turned.
• Push the motor control button with your LH (Fig. 1/F) to the stop and control the steering lever (Fig. 1/C)
with your RH at the same time.
• The sliding desk (FIG. 1/B) will go forward, pushing the stock through the knife.
The switch contact could be destroyed if the button is not pushed to the stop.
Notice: Always push the switching button completely!
48
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude W 520-5 T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude W 520-5 T in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info