624908
14
Zoom out
Zoom in
Previous page
1/48
Next page
If you want the saw jammed in the workpiece to start again, centre the circular saw blade in the cutting gap and check whether
the saw teeth are not seized in the workpiece. In case the circular saw blade is jammed, it can move outwards off the workpiece
or cause backlash if you want to start the saw again.
Support large boards to reduce the backlash risk as a result of the circular saw blade being jammed. Large boards might bend
under its weight. Boards must be supported on both sides, both near the cutting gap and on the edge.
Do not use circular saw blades that are blunt or damaged. Circular saw blades with blunt or poorly balanced teeth lead to
increased friction, jamming of the circular saw blade and backlash due to too narrow cutting gap.
Fix the set cut depth and cut angle before you start cutting. If setting changes during the cutting process, the circular saw blade
can get jammed and cause backlash.
Be especially careful at “inside cuts“ to existing walls or other sections that cannot be seen. A circular saw blade getting inside
can get blocked and cause backlash when cutting into hidden objects.
Before using the appliance you should check whether the bottom protection cover closes properly. Do not use the saw if the
bottom protection cover does not move freely and does not close immediately. Never fix the bottom protection cover in an open
position. If the saw falls on the floor in an uncontrolled manner, the bottom protection cover can get bent. Open the protection
cover with a return lever and make sure it moves freely and touches neither the circular saw blade nor other parts at any angle.
Check the function of springs for the bottom protection cover. If the bottom protection cover and springs do not work perfectly,
have a maintenance check of the saw before using it. Parts that are damaged, sticky deposits or splinter clusters slow the
working of the bottom protection cover.
Open the bottom protection cover with your hand only for special cuts like for example the “inside and angular cuts“. Open the
bottom protection cover with a return lever and keep it open until the circular saw blade gets inside the workpiece. The bottom
protection cover must work automatically for other cutting processes.
Do not put the saw on a work table or ground without the bottom protection cover covering the circular saw blade. A circular saw
blade that is unprotected and coasting moves the saw against the cutting direction and cuts everything it can. Observe the saw
coasting time.
Do not touch the splinter ejection hole with your hands. You can get injured by the rotating parts.
Do not work with the saw above your head. You do not have sufficient control of the saw in this position.
Use appropriate detectors for searching for hidden power lines or contact your local electrical energy supplier. Any contact with
the power line can cause fire and electric shock. Damage to the gas line can lead to explosion. Breaking into the water pipeline
can lead to damage or electric shock.
Do not work with the saw on the spot. The saw has not been designed for operation with the saw table.
Do not use circular saw blades out of HSS (high alloy steel for quick cuts). These circular saw blades can easily break.
Do not cut ferrous metals. Hot splinters can cause the dust catcher to ignite.
Hold the saw with both hands and secure a safe posture when working. The saw is guided safer with both hands.
Secure the workpiece. A workpiece caught in clamping devices or a vice is held safer than with your hand.
Do not put the saw aside until it stops. The extension can get jammed and lead to loss of control of the saw.
Do not use the saw if the cable is damaged. Do not touch a damaged cable and pull the plug out of socket if the cable gets
damaged during work. A damaged cable increases an electric shock risk.
Behaviour in case of emergency
Provide necessary first aid treatment corresponding to the injury nature and seek qualified medical help as soon as possible.
Protect the injured person from other injuries and calm him/her down.
Work with the hand-held circular saw
- The swivelling protection cover is automatically drawn back from the workpiece.
- Proceed smoothly and uniformly forward with the circular saw.
- Waste must be on the right to the circular saw so that the wide part of the support table could fit with its entire surface.
Technical specification
Appliance: HKS 1200 hand-held
circular saw
Voltage/frequency: 230V~50Hz
Engine power: 1,200W
Revolutions: 4,500 min
-
1
Circular saw blade
dimensions:
185mm/20mm
Cutting power 90°/45° 66mm/44mm
Noise: L
W
A
105dB
Weight: app. 8kg
Order No. 58045
Circular saw blades appropriate to the HKS 1200 hand-held circular saw
Hard-metal circular saw blade, 185 x 20 mm, 24 teeth, order No. 58337
Hard-metal circular saw blade, 180 x 20 mm, 30 teeth, order No. 58338
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude HKS 1200 58045 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude HKS 1200 58045 in the language / languages: English, German as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info