624908

Gude HKS 1200 58045 Manual

13
Zoom out
Zoom in
Previous page
1/48
Next page
- Avoid abnormal body posture.
Assume a safe posture and keep constant balance.
- Treat your tool with care.
Keep the tool sharp and clean so that it is possible to work with it better and safer. Follow the maintenance regulations and
appliance replacement instructions. Check regularly the cable of your electric tool and have it replaced by an authorised
professional if damaged. Check regularly the extension cables and replace them if damaged. Keep the handles dry and
with no oil and fat.
- Pull the plug out of socket.
If you do not use the electric tool or before maintenance and at replacement of e.g. circular saw blades, drills, etc.
- Do not leave any adjusting instruments in the appliance.
Before switching the appliance on, check whether you have removed all wrenches and adjusting instruments.
- Prevent starting with no attendance.
Do not carry the electric tool plugged in with your thumb on the switch. Make sure the switch is off when plugging into the
socket.
- Extension cables in open air.
In open air, use only extension cables approved and adequately marked for that purpose.
- Be careful.
Pay attention to what you are doing. Work reasonably. Do not use the electric tool when not concentrated.
- Check the electric tool for any damage.
Before using the electric tool again, you need to carefully check the perfect and specified working of the guard devices or
slightly damaged parts. Check whether the rotating parts work faultlessly and do not drag behind or whether any parts are
not damaged. All parts must be installed properly and satisfy all conditions to ensure faultless operation of your electric
tool. Any guard devices and parts that are damaged must be duly repaired or replaced by an authorised specialised shop
unless provided otherwise in the Operating Instructions. Have any damaged switches replaced by a customer service
shop. Do not use electric tools at which the switch cannot be turned on and off.
CAUTION
- Use only accessories or extensions specified in the Operating Instructions. Using any other extensions and accessories
can represent a risk of injury.
- This saw corresponds to appropriate safety provisions. Repairs can only be executed by a professional electrician and only
original spare parts must be used, failing which there might be injuries of the operator.
Safety instructions specific for this appliance
Do not touch the cutting area and circular saw blade with your hands. Hold the auxiliary handle or engine case by the
other hand. If both hands hold the saw, the circular saw blade cannot injure them.
Do not touch under the workpiece. The protection cover is unable to protect you against the circular saw blade under the
workpiece.
Adjust the cutting depth to the workpiece thickness. Less than one full tooth height must be seen under the workpiece.
Never hold the cut workpiece in your hand or above the leg. Secure the workpiece in stable fixture. It is important that the
workpiece is fixed well so as to minimise the risk of body contact, circular saw blade jamming or loss of control.
Grab the saw only on insulated working surfaces if you carry out works at which the extension or proper feeder cable
can become conductive. Metal parts of the saw also become conductive by getting in touch with the conductive line, which
leads to electric shock.
Always use a stop or straight edge guiding for longitudinal cutting. This improves the cut accuracy and reduces the
possibility of circular saw blade getting jammed.
Always use circular saw blades with correct size and an appropriate hole for clamping (e.g. star or round). Circular saw
blades not appropriate for assembly parts of the saw experience radial run-out and lead to loss of control.
Never use any damaged or poor washers or screws of the circular saw blade. Washers and screws of the circular saw
blade have been designed specially for your saw, optimum performance and operational safety.
Causes of backlash and protection against it:
Backlash is a sudden response as a result of seized, jammed or poorly balanced circular saw blade that causes the saw to go
up uncontrolled and then moves off the workpiece towards the operator.
When the circular saw blade gets seized or jammed in a closed cutting gap, the engine power hits the saw back towards the
operator.
If the circular saw blade is revolved or poorly balanced in the saw cut, teeth of the back edge of the circular saw blade might get
jammed in the workpiece surface, which results in the circular saw blade going up from the cutting gap and saw bouncing back
towards the operator. The backlash is a result of wrong or faulty use of the saw. It can be prevented by the appropriate safety
measures described below.
Hold the saw firmly with both hands, placing them to a position in which you are able to absorb the backlash force. Always stand
from the side of the circular saw blade; never put the circular saw blade to the same level with your body. With backlash, the
saw might bounce back but the operator can cope with the backlash force by appropriate safety measures.
If the circular saw blade gets jammed or you interrupt the work then switch the saw off and hold it easily in the workpiece until
the circular saw blades stops. Never try to take the saw away from the workpiece or pull it back if the circular saw blade is
turning, failing which you will face a risk of backlash. Find out and remove the cause of the circular saw blade getting jammed.
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude HKS 1200 58045 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude HKS 1200 58045 in the language / languages: English, German as an attachment in your email.

The manual is 1,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info