626214

Gude GBM 900 95170 Manual

37
Zoom out
Zoom in
Previous page
1/50
Next page
• Never press the forward gear and the
backward gear at the same time. The product can
be severely damaged if doing so!!!
Safety instructions for the operation
• Use the product only after you have read the operating
manual carefully.
• Follow all safety instructions stated in the manual.
• Behave responsibly against other people.
• Never try to stop the cutters or tilt the product while the
cutters are still running. Wait until the cutters stop.
• If the cutters get in touch with a contaminant, please
stop the motor immediately and check the product for
damages after the cutters stop. Resume the work only
with an undamaged product.
• Only walk during work. Do not run.
• On slopes, always work in cross direction and never in
upward or downward direction. Be very careful while
changing direction.
While crossing areas which are not planted with glass and
during transport to and from the work area, the cutters may
not be running.
Operation
- Set the desired cutting height over the runners.
- Set the switch to position “ON“
- For cold start, press “CHOKE“
- Set gas pedal to middle position
- Start with reserve starter
- Switch off “CHOKE“
- Give full throttle
- Operate gear for forward or backward movement
- Start with the mowing
As soon as the gas pedal is pressed, the cutters will start to
work.
In order to switch off the motor, set the switch to the position
OFF.
In order to move the sickle-bar mower while the motor is
switched off, remove all splint pins on the wheels, press the
wheel in direction of the product and push the splint pin back
into the spindle. (Fig. 4). Process in the reserve order in order
to re-activate the wheel drive.
Residual risks and protective measures
1. Mechanical residual risks:
• Cutting, trimming:
The running cutters can lead to severe cutting injuries
and cutting off of body parts.
Æ Always wear protective gloves. Never engage in
the running machine.
• Catch, rolling-up:
The cutters can catch cords, wires or pieces of
clothing.
Æ Search the area for possible contaminants. Keep
away from fences and wear tight-fitting clothes.
2. Electrical residual risks:
• Direct electrical contact:
The touch of the spark plug connector while the motor
is still running may lead to an electric shock.
Æ Do not touch the spark plug connector while the
motor is running.
3. Thermal residual risks:
• Burns, frostbites:
The touch of the exhaust may lead to burns.
Æ Let the product cool down.
4. Risks caused by noise:
• Hearing loss:
Frequent or lang-time work with the product without
hearing protection can lead to hearing loss.
Æ Use hearing protection.
5. Risks caused by vibration:
• Full-body vibration
Long-time work with the machine can lead to body
impairments through vibration.
Æ Have pause regularly.
6. Risks caused by materials and other substances:
• Contact, inhalation:
The inhalation of the exhaust gases can be very
harmful to health.
Æ The product may be only used outdoors.
• Fire or explosion:
The product will be driven with a easily inflammable
fuel mixture, which can be ignited during refueling for
example.
Æ Do not fuel near open fire and do not smoke while
refueling.
7. Other risks:
● Ejected objects or liquids:
Ejected stones or soil can lead to injuries.
Æ Make sure that no other people stay within the
work area and use personal protective equipment.
Maintenance and care
Safety instructions for the inspection and maintenance:
Only a regularly maintained and well serviced product can be
a satisfactory tool. Lack of maintenance and care can lead to
unexpected accidents and injuries.
• For all activities on the product, always shut down
the motor and remove the spark plug connector!
• Never use sharp cleaning tools for any kinds of
cleaning. This can lead to damages or destroy of
the product.
Inspection and maintenance plan
1. Before start of work:
• Check for loosened parts
• Check oil level and replenish oil if necessary
• Check tire pressure (for this, refer to the instructions
on the tires)
• Lubricate eccentric
• Lubricate cutter bar
2. Every 25 operating hours
37
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GBM 900 95170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GBM 900 95170 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info