626214

Gude GBM 900 95170 Manual

35
Zoom out
Zoom in
Previous page
1/50
Next page
• Use only original spare parts for the maintenance.
• Repairs may be only carried out by a professional
electrician.
• Before putting the machine into operation and
after impact of any kind, check it for sign of wear
or damage and arrange repairs if necessary.
• Never use spare parts and accessories, which are
not specified or recommended by the
manufacturer.
• Use the machine only under daylight or with
sufficient artificial lighting.
• Make sure that no other objects may cause any
short-circuit on the contacts of the product.
• This product is not a toy for children! Children can
not estimate risks caused by this product. Never let
children use this product.
• People, who are not capable to use the product
due to their physical, sensory or mental ability
or their inexperience or lack of knowledge may
not use this product.
• If the product has any obvious damages, then it
may not be put into operation.
• Severe dangers may arise through improper
repairs.
• The same requirements also apply to the spart
parts.
Güde GmbH & Co. KG will assume no liability for
damages due to the following root causes:
• Damages on the product through mechanical
impacts and excess voltages.
• Changes on the product.
• Use for purposes other than those described
in the manual.
• Pay close attention to all safety instructions in
order to avoid injuries and damages.
Important product-specific safety instructions
•
Never press the forward gear and the
backward gear at the same time. The product can
be severely damaged if doing so!!!
The oil level must be checked before you
put the product into operation each time.
Replenish oil if necessary (Motor oil 500ml
SAE30)
•
Never work on excessively steep hillsides
(max. 30°)
•
On slopes, always work in cross direction
and never in upward or downward direction. Be
very careful while changing direction.
• Pay attention to the ambient conditions, under
which you are working.
• Toxic waste gases will be generated through the motor,
as soon as the motor starts running. These gases can
be odorless and invisible. Therefore, never work with
the product in closed or badly aired rooms. Arrange for
sufficient lighting during your operation. For wet, snowy,
icy conditions, on slopes and uneven site, arrange for a
safe stand stability.
• Do not let any unauthorized people operate the
machine. Visitors and bystanders, especially children
as well as ill and weak people, should be kept away
from the work area. It should be avoided that other
people get in touch with the tools.
• Arrange for the safe-keeping of the tools. Tools,
which are not used, must be kept at a dry place, which
should be as safe as possible or is locked in an
inaccessible manner.
• Use the right tool for each activity. For example, do
not use any small tools or accessories for activities,
which must be performed with heavy tool actually. Use
tools only for the purposes, for which they are designed.
• Wear properly. The clothes must be appropriate and
may not bother you during work.
• Use personal protective equipments. Wear safety
shoes with steel toe caps/steel soles and non-slip soles.
• Wear a pair of safety glasses to protect against hurled
objects.
• Use hearing protection. Use personal noise protection
such as ear plugs.
• Wear solid gloves – gloves made of chrome leather
can provide a good protection.
• Transport. Always transport the sickle-bar mower with
wheels in transport position. While setting the machine
down, make sure that nobody will be endangered.
Protect the product against overturning, damages and
leakage of fuel.
• Remove plug key and ignition key, before the
machine is swichted on.
• Remain always alert. Pay attention to what you are
doing and use common sense. Do not use any motor
tools, if you are tired. It is forbidden to work with the
machine under the influence of alcohol, drugs or
medicaments, which may jeopardize the reaction.
• Filling von fuel. The motor must be always shut down
before filling, so that pending over-pressure can be
released slowly and no fuel will spurt out. Through
operation with the machine, high temperature will arise
on the enclosure. Therefore, let the machine cool down
before filling. Otherwise, the fuel may be ignited and
lead to severe burns. During the filling, make sure not to
fill too much fuel. If any fuel leaks, it should be removed
immediately and the product be cleaned. After the filling,
pa
y attention to the proper fit of the locking screw joint
in order to avoid the loosening caused by the arising
vibration during the operation.
• Pay attention to damaged parts. Check the tool,
before you use it. Are there any damaged part? Ask
yourself in case of slight damages seriously whether the
tool can work in an intact and safe manner nevertheless.
Pay attention to the correct alignment and setting of
moving parts. Engage the parts in a proper manner?
Are there any parts damaged? Is everything installed
properly? Are all other pre-conditions for the intact
function fulfilled? Unless otherwise specified in the
operating manual, damaged protective equipments and
etc. must be repaired or replaced properly by
authorized staff. Defect switches must be replaced by
an authorized staff. If repairs are required, please
contact your local service center.
35
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude GBM 900 95170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude GBM 900 95170 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info