628835

Gude 200-400 w 69010 Manual

10
Zoom out
Zoom in
Previous page
1/38
Next page
not take the device to refuse storal area. Herewith you will
contribute to protection of environment.
The instructions for disposal are described on pictograms
placed on the device, and/or on its packing. For the
description of individual meanings see Chapter “Marks on the
Device”.
Requirements on the Operator
The Operator should carefully read this Operation Manual
before using the device.
Qualification
The professionally adept person needs just detailed training
of how to operate the device, no special qualification is
required.
Minimum Age
The device may be operated only by persons older than 16.
The exception is when using the device by an adolescent
during his/her preparation for profession, where the device is
used for the purpose of getting skill under supervision of the
trainer.
Training
The device can be operated by a person trained by a
professionally adept worker or be trained according to the
Operation Manual. No special training is necessary.
Technical Data:
Assortment Position No. 69010
Permanent output [W] 200
Max. output [W] 400
Inlet voltage [VDC] 10-15
Outlet voltage [VAC] 220-240
Frequention [Hz] 50
Wave shape
Modifed sinusoid wave
Efficiency 90%
Permanent current force
[mA]
250
Protection against low
voltage [V]
10±0,5
Caution – low voltage [V] 10,5±0,5
Protection against
overvoltage [W]
200
Cabel length [cm] 76
Fan Yes
Protection
Protection against
overloading, protection
against overheating,
protection agains shortcut,
protection against reverse
of poles
Operation
Battery Alarm Signal
• As soon as supply voltage of the battery drops under
10,5 V, the alarm signal sounds.
• Disconnect all appliances from the Voltage Changer.
• Disonnect the Voltage Changer from the battery.
• Battery shall be immediately charged so that the
damage on battery may be prevented.
• The Voltage Changer will disconnect all appliances from
the battery beginning with the value of 10 V, for
prevention of excessive discharge of the battery.
• Should the alarm signal sound although the voltage is
sufficient, there si another problem. In this case refer to
Chapter “Repair of Defects”“
• Instruction: A short alarm signal may sound during the
connecting the Voltage Changer with terminals and its
disconnecting. It is a common feature and it does not
indicate a problem on the device or any failure..
Service Life
• Usually one charging of the battery that is in good
condition is sufficient for 1 to 2 hours of operation. The
duration depends particularly on the connected
appliances.
• In order to prevent too high decrease of the battery
voltage, start the vehicle engine after an hour and
disconnect all appliances (light, ventilation, radio etc.)
Protective Mechanisms
The Voltage Changer supervises continuously a few
parameters of power supply and current consumption.
Autorestart Function
The device automatically switches the device on after it has
been repaired (switching of the protection). The fuse need not
be replaced.
Low Voltage
Should the Changer alarm signal sound reporting the low
voltage (from 10,5 V), it is not dangerous for the Changer.
The alarm signal serves for signalization of decrease of
supplying battery voltage. As soon as the voltage drops under
10 V, the device will disconnect the appliances.
Shortcut
By shortcut supervision can be checked if the connecting
cables have not reversal polarity or if there is a shortcut in the
system. Should this protection respond, disconnect the
appliances from the Changer and check all supply lines of the
Changer.
Overheating
As soon as tempereture of internal cooling bodies exceeds
65 °C, the protection relais of the Changer will disconnect
appliances, so that the device may be cooled. After the
Changer has been cooled, it is automatically reswitched. No
intervention of user is needed. Check if the appliances do not
consume too much current, disconnect them if necessary.
Overloading
The Voltage Changer will automatically switch off if the
appliances consume more permanent and/or closing current
than the values the device is designed for (see the Cahpter
“Technical data”). Disconnect large appliances. The device
will automatically switch on as soon as the loading fluctuates
within normal range.
Failures-Causes-Repairs
CAUTION: FIRST CHECK PROTECTION MECHANISMS !
Before all works on the device pull out the plug from the
network..
• The plastic parts are cleaned with a wet cloth. Do not
use any detergents, solvents or pointed things.
Safety Instructions for Inspection and Maintenance
Only the device on which regular maintenance is performed
and which is well cared for will be helpful. Failures in the
maintenance and care may cause unpredictable accidents
and injuries..
10
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gude 200-400 w 69010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gude 200-400 w 69010 in the language / languages: English, German, Danish as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info