Manual Gude 200-400 w 69010 (page 9 of 38) (English, German, Danish)

628835

Zoom out

Zoom in

1/38

Ventilation

IMPORTANT ! Do not cover Voltage Changer (e.g. with a

scarf) and remove all things in the radius of 50 cm .This

safety measures are necessary to protect the device against

overheating.

Assembly and First Putting into Operation

# 69010 is to be connected with the 12 V battery by means of

the cigarette lighter or by means of the adapter with 12 V

battery.

Explanation to the Figure.:

An-/ Aus-Schalter -switch ON/OFF

Betriebsanzeige - indicator of operating condition

Niederspannung - low voltage

Steckdose - socket

Anschlüsse - connections

Sicherung - fuse

Ventilator - fan

• 12 V bartery should supply 11 to 15 V voltage and

sufficient current. To receive rough calculation of the

current capacity, divide the input power of the appliance

in watts by ten (10), and you will get approximate

calculation of necessary number of Amperes. Example:

300 W appliance.

Input power 30 Amperes (300:10).

• The Voltage Changer shall be placed on flat base, if

possible (e.g. the seat or the floor), the place of location

shall meet also following conditions:

• In dry: Keep the device in safe distance from water. The

device shall be placed so that spraying or dropping

water could not get into it.

• In cold: Environment temperature shall be in range

between 10 °C to 26 °C. Do not place convertor near the

heating devices or venting holes. Prevent impact of

direct sunshine.

• Ventilation: Keep the distance for ventilation, at least 3

cm from the surrounding, so that sufficient ventilation

may be guaranteed. Never cover the ventilating holes.

• Securing: Never place the Voltage Changer in vicinity of

flammable explosive and easy to ignit materials and

liquids. Never install the device when driving. The design

of the terminals and the length of cables are not

designed for this purpose.

• The device shall not be used on positively earthed

electric systems.

• The device may be connected to power source only

when it is switched off.

• Connect the Voltage Changer with the 12V battery by

means of the supplied cigarette lighter adapter (only at

the assortiment position number 69010) or by means of

terminals. Use always only one connecting cable, never

both cables in the same time. When using adapter,

insert the adapter simply into a suitable socket/cigarette

lighter. When using terminals, make sure the

individual connections are correctly poled! The red

terminal (positive pole) shall be connected to

corresponding positive pole of 12 V battery and black

terminal (negative pole) to negative pole. When using

the terminals the car shall not be in motion. Before

driving on the terminals shall be removed.

• If the Voltage Changer is not to be used for a longer

period of time, disconnect the Changer from the battery

system.

• When the buzzer start to sound, proceed as follows:

switch dhe device off, disconnect the Voltage Changer

from the battery system and switch again the engine of

your car. The alarm sound refer to indication Lo-Bat and

indicates that the battery voltage is low. Should you fail

to switch the engine again and use on the Voltage

Changer, it will switch off automatically. Therefore the

battery of your car will have only about 10.5 V/DC. This

is sufficient for repeatedly switching the engine and use

of Voltage Changer. This is how you may avoid empty

battery.

• It would be better to let the engine run for 10 to 20

minutes whenever the Voltage Changer has been used

for 2 to 3 hours. Then the battery can be charged again

and the enormous discharging may be prevented.

• Make sure that the Voltage Changer is disconnected

from the battery before you start using charging device

for putting the battery into operative condition again.

Should you fail to do so and should you simply connect

the charging device, it may cause peak voltage that may

damage the Voltage Changer. – THEN THE

GUARANTEE EXPIRES!

• Make sure the voltage never exceed value of 15VDC –

THE VOLTAGE CHANGER MIGHT BE DAMAGED –

THE GUARANTEE EXPIRES!

• Please observe following when connecting a device to

the Voltage Changer: in many devices the nominal

output and NOT starting-up output is given. The Voltage

Changers are furnished with the overvoltage protection

so that the connected devices may sometimes start up

with difficulties or cannot start up at all. Read carefully

the Operation Manual of your device so that you may get

to know the maximum output, or contact the

Manufacturer.

Electric residual dangers

Direct electric contact

Defective cable or plug may cause electric accident.

Defective cable or plug shall always be replaced by a

specialist.

Indirect electric contact

Injury caused by parts under voltage on open electric

parts or on defective parts

At maintenance works the plug shall always be pulled out of

the network.

Unpro

per local lighting

Insufficient lighting represents high safety risk.

When working with the device sufficient lighting shall be

ensured.

Heat residual dangers

Burn

Touch on the Voltage Changer during its operation and during

the coolling stage may cause burn.

Let the devices after operation get cool first.

How to proceed in emergency

Introduce the first aid measures that are necessary

according to the injury and call qualified medical aid as

soon as possible.

Secure the injured against any other damage and put him in

restive conditions.

Disposal

For disposal of the device contact your local dealer or local

recycling enterprise. The device shall not be under any

circumstances disposed of in common domestic refuse! Do

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gude 200-400 w 69010 in the language / languages: English, German, Danish as an attachment in your email.

The manual is 0,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gude 200-400 w 69010 Manual

Product: