633024
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
- EMERGENCYDISARMING.
In case of emergency (i.e. handset low battery) it is possible to disarm the system placing on the
RECEPTACLE the electronic key integrated in the GT889 handset.
- IN CASE OF ALARM.
- Pressing the “OFF” handset button or approach with the handset in AUTOMATIC-TRANSMISSION-
LINK mode” to disarm the system.
Note: it is possible to stop the alarm without disarming the system pressing the ON GT889 handset
button.
- PRE-ALARM BY LINK.
If the system has been armed due to the “LINK” absence, the alarm causes are preceeded by a pre-
alarm with BEEP and INDICATORS FLASH for 10 seconds.
- ANTI-HIJACK.
This function allows to block the motor vehicle in case the user is obliged to leave it with the engine on
( theft attempt).
A - AUTOMATIC ANTI-HIJACK.
The operation occurs only by the GT884N (optional) handset in “AUTOMATIC TRANSMISSION-
LINK” mode and with the Function No. 8 - AUTOMATIC ANTI-HIJACK enabled.
1 - With the ignition key on the LED illuminates constant RED to indicate that the anti-hijack procedure is
reserved. If the LINK signal is missing for more than 30 seconds the system enters the anti-hijack
phase.
2 -The LED illuminates constant GREEN.
3 - After 15 seconds the indicators start flashing.
4 - After other 15 seconds the system emits an alarm cycle with a duration of 30 seconds. If the ignition
key condition continues another alarm cycle is generated.
5 - When the ignition key is switched off, the engine immobilisation is activated and it will block the
starting. To the following vehicle ignition attempts an alarm cycle will be generated.
6 - To come out from the anti-hijack phase, in any phase, it is necessary to have the same handset in
AUTOMATIC-LINK TRANSMISSION which has activated the function and to get closer to the motor
vehicle.The confirmation is given by two flashes of the indicators, by two beeps and by the LED
switching off.
B - MANUAL ANTI-HIJACK.
The operation occurs only by the GT889 handset enabled for ANTI-HIJACK.
1 - With the ignition key on press the GT889 “SERVICE” handset button.
2 -An indicators flash and the GREEN LED switching on confirm that the ANTI-HIJACK function has
been activated.
3 - After 15 seconds the indicators start flashing.
4 - After other 15 seconds the system emits an alarm cycle with a duration of 30 seconds. If the ignition
remains on another alarm cycle is generated.
5 - When the ignition key is off the engine immobilisation is activated and it stops the vehicle starting. An
alarm cycle will be generated by attempting to start the vehicle.
6 - To come out from the anti-hijack state, from any phase, it is necessary to have the same GT889
remote control handset which has activated the function and press the “SERVICE” handset button. The
operation will be confirmed by two indicators flashes, two siren Beeps and by the LED switching off.
ENABLE/DISABLE THE ANTI-HIJACK FUNCTION:
1 - Open the GT889 remote control handset, remove the battery and wait the led signalling.
2 - Press the "OFF" button and close the remote control handset.
3 - Keeping the "OFF" button depressed insert the battery in the remote control handset and wait the
led signalling.
4 - If the led remains illuminated constant the function is ENABLED, if the led flashes the function is
DISABLED.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 970 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 970 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info