633024
9
Zoom out
Zoom in
Previous page
1/12
Next page
9
5 - Release the "OFF" button and close the remote control handset.
6 - To change the function state repeat the procedure from the point 1 (at each repetition of the
procedure the function changes state).
- PROTECTIONS.
When the system is armed the status check LED switches constant on, after 30 seconds the LED
flashes. The ignition key, seat/bonnet/sidestand and wires cut protections are active 5 seconds
after the arming, while the shocks/movement sensor is active when the status check LED
flashes.
- SLEEP MODE (POWER SAVE).
To protect the motor vehicle battery the system operates a constant monitoring of the power supply
voltage and/or reduction of the available functions in the time.
MOTOR VEHICLE BATTERY MONITORING: when the system is disarmed, if the battery reaches the
threshold of 8V the alarm places in “SLEEP MODE” .
SLEEP MODE WHEN THE ALARM IS DISARMED: when the alarm is disarmed, after 10 days the system
places automatically in “SLEEP MODE”. To reactivate the alarm switch the ignition key on.
SLEEP MODE WHEN THE ALARM IS ARMED: after 5 days the system doesn’t accept the handset
command anymore, but all the protections remain active. The normal operation is restored in case of
alarm. In this condition the first cycle is preceeded by a pre-alarm signal (beeps) of 10 seconds.
During the pre-alarm it is possible to disarm the system.
- INDICATORS EMERGENCY FLASH (only with GT889).
- To activate the indicators flash turn the motor vehicle ignition key on and press the “OFF” handset
button. Note 1: the flash continues even removing the key. Note 2: during the indicators flash is
however possible to arm/disarm the system.
- To stop the indicators flash turn the motor vehicle ignition key on and press the “OFF” handset button.
- SERVICE MODE.
For the motor vehicle servicing, i.e. in winter, it is possible to place the alarm in SERVICE MODE.
1 - Turn the ignition key on and press the “ON” handset button. The system confirms the operation with
3 flashes of the RED LED.
2 - Turn the ignition key off and after 120 seconds the system places in POWER SAVE with a current
consumption of very few microampere.
3 - To come out from the SERVICE MODE switch the ignition key on and arm the alarm with the handset
during the 120 seconds.
- BACKUP BATTERY RECHARGE.
The device is equipped with internal battery to manage possible alarms due to tamperings on the
electrical system when the thesystem is armed. The battery recharge occurs only with the motor
vehicle ignition switched on. To recharge completely the battery 24 hours are needed.
- ALARMS CHECK CONTROL AND ANOMALIES.
If during the surveillance state an alarm has been detected (4 indicators flashes and 4 beeps to the
disarming) or there is anomaly it is possible to check the cause.
When the alarm is disarmed switch the ignition key on and check the LED flash as indicated in the
ALA RMS SIGNAL TABLE and ANOMALIES SIGNALS TABLE.
- Motor vehicle low battery indication: when disarming with the handset if the motor vehicle
battery is at 11,6V the system doesn’t activate the indicators and after the normal acoustic signalling
emits 5 anomaly beeps and when it is triggering it doesn’t activate the indicators.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 970 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 970 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info