633024
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
- RAPID TEST (Function No. 4).
With this function it is possible to check the correct system installation carrying out a test of
all the alarm lines.
SEAT/BONNET/SIDESTAND test switch: if the alarm line is triggered the system generates
5 beeps and 5 GREEN flashes of the LED on the receptacle.
SHOCKS/MOVEMENT SENSOR test: to test the position sensor it is necessary to wait 5
seconds from the function enabling before moving the motor vehicle. When the movement
is detected the system generates 2 beeps.
Ignition switched live test: if the alarm line is triggered the system generates 6 beeps and
6 flashes of the GREEN LED on the receptacle.
Wires cut test: removing the power supply to the alarm system a continuous s equence of
beeps will follow. To come ou from the function deactivate the system by the “OFF” button or
wait 30 seconds without triggering the alarm lines. In both ways you come out also from the
set functions.
- ACOUSTIC SIGNAL WHEN ARMING/DISARMING (Function No. 5).
It is possible to program the acoustic signal (beep) to indicate the alarm arming and the
disarming.
1 - Select the function and ENABLE/DISABLE pressing the “OFF” handset button.
- POSITIVE OUTPUT WHEN THE ALARM IS ARMED (Function No. 6).
This output, if enabled, is active 5 seconds after the arming, it can be used to command an
additional module or a satellite system.
1 - Select the function and ENABLE/DISABLE pressing the “OFF” handset button.
- INDICATORS EMERGENCY FLASH (Function No. 7).
This function allows to activate the four emergency flashes (hazard warning) pressing the
“OFF” remote control handset button with ignition key ON. The flash continues even removing
the vehicle ignition key. It is possible to activate and deactivate the system. To switch OFF
the four emergency flashes press the
“OFF” remote control handset button again with the
ignition key ON.
1 - Select the function and ENABLE/DISABLE pressing the “OFF” remote control handset
button.
- AUTOMATIC ANTI-HIJACK (Function No. 8) (Available only with
GT884N).
This function allows to block the motor vehicle in case the user is obliged to leave it with the
engine on ( theft attempt).
1 - Select the function and ENABLE/DISABLE pressing the “OFF” handset button.
- HANDSETS SELF-CODING (Function No.3).
With the function No. 3 it is possible to self-code new handsets to the control unit up to a
max. of 8.
1 - Select the function and press the “ON” button to be self-coded.
2 - The system confirm the correct handset self-coding by a flash of the GREEN LED and
by a beep.
WARNING:
- When you have entered the function the first handset which is self-coded deletes all
the other handsets memorised.
- If you want to add one or additional handsets you have to self-code all of them.
- If you try to self-code an handset already self-coded or the handsets maximum
number has been reached the system emits 3 anomaly beeps.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 970 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 970 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info