633024
5
Zoom out
Zoom in
Previous page
1/12
Next page
5
To come out from the SET FUNCTIONS:
Wait the end of the signal and place the GT889 handsets contacts to the receptacle (not
during the Function No. 3 - HANDSETS SELF-CODING). The exit is confirmed by the Led
switching off and by 5 beeps.
In the “FUNCTIONS TABLE” are mentioned the functions which can be selected.
SELF-CODING emergency procedure.
In case of GT889 handset-electronic key loss it is possible to enter the SET FUNCTIONS:
A - With the alarm disarmed disconnect the power supply and wait 1 minute.
B - Short-circuit the RECEPTACLE/LED with a metallic body the RECEPTACLE/LED
contacts.
C - Reconnect the power supply.
D - Turn the ignition key on-off 4 times (make a pause of 2 seconds at each state).
E - When the SET FUNCTIONS has been entered, this is confirmed by 5 BEEPS and by
the RED LED constant switching on.
F - Remove the short-circuit between the RECEPTACLE/LED contacts and proceed as
indicated in the self-coding procedure.
SET FUNCTIONS TABLE
FUNCTION STATE
No. DESCRIPTION
ENABLED DISABLED
1
SHOCKS/MOVEMENT SENSOR
SENSITIVITY ADJUSTMENT
GREEN
11
HIGH
RED
11
MEDIUM/HIGH
2
SHOCKS/MOVEMENT SENSOR
SENSITIVITY ADJUSTMENT
GREEN
22
MEDIUM/LOW
RED
22
LOW
3
REMOTE CONTROL HANDSETS
SELF-CODING
RED
33
NOT
AVAILABLE
4
RAPID TEST
RED
44
NOT
AVAILABLE
5
ACOUSTIC SIGNAL WHEN
ARMING/DISARMING
GREEN
55
RED
55
6
POSITIVE OUTPUT WHEN THE
ALARM IS ARMED
GREEN
66
RED
66
7
EMERGENCY INDICATORS
FLASH
GREEN
77
RED
77
8
AUTOMATIC ANTI-HIJACK
GREEN
88
RED
88
FUNCTION STATE
FUNCTION STATE
N1
N
N
2
N
N = N = Function No.
N = Led flashes No.
N = Beep No.
12
1
2
DEFINITE SETTING OUT
LEGEND:
- SHOCKS/MOVEMENT SENSOR SENSITIVITY ADJUSTMENT (Function No. 1 No. 2).
With this function it is possible to adjust the shocks/movement sensor sensitivity choosing
between 4 levels: high, medium/high, medium/low and low.
1 - Select the function and ENABLE/DISABLE pressing the “OFF” remote control handset
button.
Note: on the Led it is visualised only the active adjustment. For example if it is active the
High sensitivity the Led will emit 1 green flash during the function 1 and during the function
2 you will obtain 2 beeps without any Led signal.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 970 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 970 in the language / languages: English as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info