570171
10
Zoom out
Zoom in
Previous page
1/21
Next page
Because the receiver only allows 4-place entries, the first
place is neither entered nor displayed.
Example:
ARD transmission frequency on Astra: 11494 MHz
Receiver input: 11494
ZDF transmission frequency on Astra: 10964 MHz
Receiver input: 11964
Enter the satellite transmission frequency. This requires the
correct selection of the oscillator frequency 9.75 or
10.00 GHz (refer to the section "Entering the LNC Oscillator
Frequency").
For LNC´s with an oscillator frequency other than 9.75 or
10.00 GHz, you must select 10 GHz. When this is the case,
the programme frequency to be set does not agree with the
satellite´s transmission frequency. Determine the correct fre-
quency by subtracting the LNC frequency from the satellite
transmission frequency.
Examples:
Transmission frequency of ARD with Astra: 11494 MHz
LNC fre
quency: 19665 MHz
Frequency to adjust: = 1829 MHz
Transm. frequ. of PRO 7 with Kopernikus: 12559 MHz
LNC fre
quency: –11475 MHz
Frequency to adjust: = 1084 MHz
Selecting vertical/horizontal polarization
Press the V/H button. The following appears in the display:
Selection can be made between V1, H1, V2 and H2 using the
ɼɦbuttons.
The LNC power supply amounts to 14 volt "vertical" and 18
volt "horizontal". Note that V2 and H2, a switching frequency
of 22 kHz is superimposed on the LNC voltage 14/18 volt.
For LCDs with magnetic polarizer, the corresponding the
skew optimal value must be adjusted after polarization selec-
tion. (See chapter "ALL" – Accepting the skew value).
Pressing V/H again displays the input ("In A" or "In b"), which
is selected by the
ɼɦ button. (See chapter on selcting aerial
input).
10
After switching on with the power button, ßQ the receiver
automatically reselects the most previous programme
position (Last Station Memory).
Select the programme position with the remote control button
ɼɦ or with the numeric or programme buttons
ǵ
Ƕ
.
The display indicates the selected programme position and
the corresponding programme position number appears on
the screen as well, though briefly.
The receiver is switched on from stand by with the the
ɼɦ
buttons or with the remote control numeric buttons. The
receiver is switched on to the last selected programme with
programme buttons
ǵ
Ƕ
. The Last-Station Memory
applies in this situation as well.
Selecting programme/frequency
You can switch between the programme position and fre-
quency input mode using the P/F button. Programme
positions P1 to P199 and in frequency mode from 700 to
2050 MHz are indicated in the display.
The actual reception range of your unit depends on the LNC
used in each case.
9.75 GHz LNC:
10.00 GHz LNC:
Indication range -
of receiver:
When selecting the input frequency, take care that the set fre-
quency lies within the actual reception range of your LNC.
A direct. frequency input is possible using the remote control
numeric buttons.
The frequency can be advanced upwards using the
ɦ button
in 10 MHz increments and moved down using the ɼ button in
3 MHz increments.
You can tune the entire frequency range forward in "rapid
motion" and slower going backwards.
The frequency changes to 0.5 MHz increments with single
steps and corresponds to the finetuning.
Because the receiver only allows 4-place entries, the first
place is neither entered nor displayed.
Example:
ARD transmission frequency on Astra: 11494 MHz
Receiver input: 11494
ZDF transmission frequency on Astra: 10964 MHz
Receiver input: 11964
Enter the satellite transmission frequency. This requires the
correct selection of the oscillator frequency 9.75 or
10.00 GHz (refer to the section “Entering the LNC Oscillator
Frequency”).
(10)700 MHz (1)1800 MHz
(10)910 MHz (1)2050 MHz
(10)700 MHz (1)2050 MHz
Receiver Buttons and Functions
HI
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig STR 312 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig STR 312 in the language / languages: English as an attachment in your email.

The manual is 0,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Grundig STR 312

Grundig STR 312 User Manual - German - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info