544906
55
Zoom out
Zoom in
Previous page
1/92
Next page
55 / 92 EN
Washing Machine / User‘s Manual
3 Installation
Refer to the nearest Authorised Service Agent
for installation of the product. To make the
product ready for use, review the information
in the user manual and take care that the
electricity, tap water supply and water
drainage systems are appropriate before
calling the Authorized Service Agent. If
they are not, call a qualified technician and
plumber to have any necessary arrangements
carried out.
C
Preparation of the location and
electrical, tap water and waste water
installations at the place of installation is
under customer's responsibility.
B
WARNING: Have the installation
and electrical connections of the
product made by the Authorized
Service Agent. Manufacturer shall not
be held liable for damages that may
arise from procedures carried out by
unauthorized persons.
A
WARNING: Prior to installation,
visually check if the product has any
defects on it. If so, do not have it
installed. Damaged products cause risks
for your safety.
C
Make sure that the water inlet and
discharge hoses as well as the power
cable are not folded, pinched or
crushed while pushing the product into
its place after installation or cleaning
procedures.
3.1 Appropriate
installation location
Place the product on a rigid floor. Do
not place it on a long pile rug or similar
surfaces.
Total weight of the washing machine and
the dryer -with full load- when they are
placed on top of each other reaches to
approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient
load carrying capacity!
Do not place the product on the power
cable.
Do not install the product at places where
temperature may fall below 0ºC.
Place the product at least 1 cm away from
the edges of other furniture.
3.2 Removing packaging
reinforcement
Tilt the machine backwards to remove
the packaging reinforcement. Remove the
packaging reinforcement by pulling the ribbon.
3.3 Removing the
transportation locks
A
WARNING: Do not remove the
transportation locks before taking out
the packaging reinforcement.
A
WARNING: Remove the
transportation safety bolts before
operating the machine! Otherwise, the
product will be damaged.
1 Loosen all the bolts with a suitable spanner
until they rotate freely (C).
2 Remove transportation safety bolts by
turning them gently.
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig GWN 47230 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig GWN 47230 in the language / languages: German as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info