644728

Greenworks 20157 - G-MAX 40V Manual

20
Zoom out
Zoom in
Previous page
1/124
Next page
ENGLISH
(Original instructions)

Ƈ Make sure the tool is running at full speed before making
a cut.
sideways movement of the tool.
Ƈ Guide the tool through the branch using light pressure.
When cutting heavy branches, where a partial cut may
splinter and damage the tree, proceed as follows:
underside of the limb. Use the top of the guide bar (6)
to make this cut.
- Cut one third through the diameter of the limb. Then cut
down from the top.
Cleaning, maintenance and storage
Your Greenworkstools corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Ƈ Switch off and unplug the appliance/tool
Ƈ Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack
Ƈ Or run the battery down completely if it is integral and
then switch off
Ƈ Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in you appliance/tool/
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do not
use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust from
After use and before storage
Ƈ Regularly clean the ventilation slots with a clean, dry paint
brush.
Ƈ To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Ƈ Remove debris using a hard brush.
Ƈ Lubricate the chain with oil.
Warning! Always wear protective gloves when installing or
removing the saw chain. The saw chain is sharp and can cut
you when it is not running.
Ƈ
Ƈ
Loosen the screws (16) .
Remove the screws.
Ƈ Remove the sprocket cover (5).
Ƈ Turn the screw (18) counterclockwise to allow the guide
bar (6) to recede and to reduce the tension on the saw
chain (7).
Ƈ Remove the old saw chain from the sprocket (19) and the
guide bar (6).
Ƈ Place the new saw chain in the groove of the guide bar
and around the sprocket. Make sure that the teeth are
facing the correct direction by matching the arrow on the
saw chain with the arrow on the housing.
Ƈ Make sure that the slot (20) in the guide bar is over the
location pins (21) and that the hole (22) below the slot is
located over the adjustment pin (23).
the screws (16).
Ƈ Tighten the screws (16).
Ƈ Adjust the chain tension as described below.
Ƈ Check the saw chain tension. The tension is correct
when the saw chain (7) snaps back after being pulled
away 3 mm from the saw chain bar with light force from
between the guide bar (6) and the saw chain (7) on the
underside.
To adjust the tension:
Ƈ Loosen the screws (16).
Ƈ Turn the screw (18) clockwise.
Warning! Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the bar and chain.
Ƈ Once the chain tension is correct, tighten the screws (16).
Warning! When the saw chain is new, check the tension
stretches slightly.
Oiling the chain
The saw chain must be oiled before each use and after
cleaning using only the correct grade of oil (cat. no. A6027).
Ƈ Oil the whole saw chain (7) evenly.
Storage
When the tool will not be used for several months, ideally
leave the battery connected to the charger.
Otherwise proceed as follows:
Ƈ Fully charge the battery.
Ƈ Remove the battery from the tool.
Ƈ Store the tool and battery in a secure and dry location.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks 20157 - G-MAX 40V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks 20157 - G-MAX 40V in the language / languages: All languages as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info