7 -Mettre l’Ailette AP en faisant coïncider ses 2 orifices avec les 2 orifices de la pièce PEU. Puis placer l´autre Ailette AP et les fixer avec 2 vis
TM640.(Mettre les ailettes AP, après avoir introduit les supports montés dans la fosse préparée auparavant).
8 - Fixer provisoirement (avec 2 vis T) dans la partie supérieure du PV1335 la pièce PER comme s’il s’agissait d’un couvercle, avec la languette
tournée vers l’intérieur de la piscine, (pour aider à fixer la tôle à la zone centrale de la piscine).Il faudra lever un peu lePER lorsque vous mettrez
la plaque (Page 21) pour que la pièce PER retienne la plaque (CH) à la partie supérieure.
7 – Place a plate AP so that its two holes coincide with the two holes in the part PEU. Then place the other part AP and fasten it using 2 TM640
screws.(Before fitting the plates AP it is best to introduce the assembled beams in the ditch already prepared).
8 - Using 2 T screws, provisionally attach part PER to the top of post PV1335 as though it was a lid, with the tab towards the interior of the pool
(This will help you to mount the plate in the central area of the pool).Vertical post PER will have to be raised slightly when the wallplate is inserted
(page 21) so that part PER presses against the top of the wallplate (CH).
7 - Legen Sie einePlatte AP so, dass deren zwei Bohrungen auf die beiden Bohrungen des Teils PEU treffen. Platzieren Sie dann eine zweite
Platte AP und befestigen Sie sie mit 2 Schrauben TM640. (Die Platten AP sollten zweckmäßigerweise verlegt werden, wenn Sie die bereits
montierten Träger in den vorbereiteten Bodeneinschnitt einlassen).
8 -Verschrauben Sie Teil PER (provisorisch mit 2 Schrauben T) oben am PV1335 wie eine Abdeckung und mit der Zunge zum Poolinnern
gerichtet. (Das Befestigen des Blechs im Mittelbereich des Pools wird dadurch erleichtert)Wenn Sie das Blech (Seite 21) einsetzen, damit das
Blech (CH) oben vom Teil PER gehalten wird, muss PV1 etwas angehoben werden.
7 -. Situare un’Aletta AP in modo che i suoi 2 fori coincidano con i 2 fori che ha il pezzo PEU. Situare quindi l’altra Aleta AP e fermarli con 2
vitiTM640. (La collocazione delle alette AP è consigliabile eseguirla quando si inseriscono le travi montate nel fosso già pronto).
8 -.Avvitare (con 2 viti T provvisorie) sulla parte superiore del PV1335 il pezzo PER, come se fosse un coperchio e con la linguetta verso l’interno
della piscina (ciò aiuterà a fermare la lamiera nella zona centrale della piscina).Si dovrà sollevare leggermente il PER nel situare la lamiera
(pag.21), affinché il pezzo PER fermi la lamiera (CH) sulla parte superiore.
7- Situeer een metalen plaat AP
op zodanige wijze dat de twee gaten daarvan overeenkomen met de twee gaten die zich in het onderdeel
PEU bevinden. Plaats vervolgens de andere metalen plaat AP en zet deze vast met twee schroeven TM640 (het is raadzaam de plaatsing van
de metalen plaat AP uit te voeren wanneer u de gemonteerde balken in de reeds gereedgemaakte geul gaat inbrengen).
8 -Schroef (provisioneel met 2 schroeven T) aan de bovenkant van PV1335 het onderdeel PER aan, alsof we te maken hebben met een deksel,
met de tong naar de binnenkant van het zwembad. (dit zal u helpen de wand vast te maken in het centrale deel van het zwembad). U zult de
PER eenweinig moeten opheffen wanneer u de wand (zie blz. 21) gaat plaatsen, opdat het onderdeel PER de wand (CH) aan de bovenkant
vastzet.
7 - Situe uma Aleta AP de maneira que os 2 orifícios coincidam com os 2 orifícios que leva a peça PEU. Depois, coloque a outra Aleta AP e
sujeite com 2 parafusos TM640. (Aconselha-se efectuar a colocação das aletas AP quando inserir as vigas montadas na vala já preparada).
8 - Fixe provisoriamente (com 2 parafusos T) na parte superior do PV1335a peçaPER como se fosse uma tampa e com a lingueta para o
interior da piscina, (isto ajuda a sujeitar a chapa à zona central da piscina).Terá de levantar ligeiramente o PER quando colocar a chapa (pag.21)
para a peça PER sujeitar a chapa (CH) na parte superior.
7 - Situe una Aleta AP de manera que sus 2 orificios coincidan con los 2 orificios que tiene la pieza PEU.A continuación situe la otra Aleta
AP y sujete con 2 tornillos TM640. (La colocación de las aletas AP conviene realizarla cuando introduzca las vigas montadas en la zanja ya
preparada).
8 - Atornille ( con 2 tornillos T provisionalmente )en la parte superior del PV1335 la pieza PER como si fuera una tapa y con la lengueta hacia
el interior de la piscina. (Le ayudará a sujetar la chapa en la zona central de la piscina).Tendrá que levantar un poco el PER cuando coloque
la chapa (pag. 21) para que la pieza PER sujete la chapa ( CH ) en su parte superior.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for GRE Haiti at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of GRE Haiti in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.
The manual is 5,14 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
