467070
20
Zoom out
Zoom in
Previous page
1/33
Next page
3938
16. Error and warning messages
The charger incorporates a wide range of protective and monitoring systems designed to check the
charger’s functions and monitor the state of its electronics. If any of the unit’s limit values are exceeded,
in some cases the unit’s settings are automatically reduced (e.g. charge or discharge current); in others
the charge process is switched off (e.g. car battery almost flat).
The liquid crystal screen displays the cause of the error. Most error message are self-explanatory, but
you may find the following list useful when fault-finding. The warning message and the audible warning
signal can be switched off by pressing the “ENTER” button.
Automatic current limiting
___________ _____
___________ _____NiCd-Man. 010:43
1,50 01735 23,45
MAX.
___________ _____
___________ _____NiCd-Man. 010:43
3,75 01735 23,45
*ready*
When a charge / discharge program completes its cycle, the
screen displays the program name alternating with the mes-
sage “Completed”. At the same time the integral buzzer sounds,
in accordance with the settings you have made under “Button
click / buzzer”.
If you set a charge / discharge current which the ULTRAMAT
25 cannot deliver because it falls outside its technical limits,
the unit automatically reduces the current to the maximum
possible value. To warn you of this, the screen displays the
charge / discharge current which is actually flowing, alterna-
ting with the warning message “MAX”.
Possible causes of an automatic reduction include:
- High cell count combined with high discharge current; the maximum discharge power is 50 Watts.
- Converter power insufficient to produce the selected charge current.
- Overload protection - current reduction protects the unit from overloading.
- Car battery voltage too low to supply the selected charge current.
Pb charge programs:
In the Pb charge programs the screen displays the message MAX when the charger has automatically
reduced the set charge current because it is too high for the battery on charge.
“Completed” message
Display of car battery voltage
___________ _____
___________ _____NiCd-Auto 010:43
car batt. 12,8V
The actual car battery voltage can be called up during any
charge / discharge process by pressing the INC and DEC but-
tons
simultaneously.
Note: the car battery voltage
cannot be displayed if a charge /
discharge program is not currently active.
DECINC
___________ _____
___________ _____
*****ERROR******
car batt. empty
This warning message is displayed if the voltage of the car
battery falls
below the value selected in the program menu
“Low voltage cut-off” in the user settings (11.5 V or 10.8 V).
14. Screen displays
Battery voltage
________________
________________
NiCd-Man. 010:43
3,75 01735 23,45
Charge / discharge program Charge / discharge time
Charge / discharge current
Capacity
The essential information relating to the current charge / discharge process is displayed in clear form on
the two-line liquid crystal screen; the screen also indicates that the buzzer is sounding. The previously
displayed values can then no longer be called up.
15. Screen monitor displays
The charger incorporates a wide range of protective and monitoring systems designed to check the
charger’s functions and monitor the state of its electronics. If any of the unit’s limit values are exceeded,
the charge process is switched off. Typical triggers would be excess voltage, excessive temperature or
a depleted car battery.
If any of these problems occur, the liquid crystal screen displays the cause of the error, and the buzzer
sounds to alert you.
___________ _____
___________ _____
cycl. D 1 010:43
1,50 01735 23,45
When the cycle program has been started, the screen dis-
plays at top centre the progress of the program: “L” stands for
Charge and “E” for Discharge. The number after the letter indi-
cates the number of the current cycle.
A display of individual cycle data is
only available when you
have selected the NiCd balancing program, and the cycle in-
formation is only retained until the battery is disconnected, or
until you interrupt the program by pressing the MODE button.
When you do this, the data is reset to “00000”.
Pressing the INC button takes you to a display of the individual
data sets, and each successive press of the INC button swit-
ches to the next set of cycle data. Pressing the DEC button
cycles back through the displayed data.
Display of individual charge cycles
(NiCd balancing program only)
DECINC
___________ _____
___________ _____
Cycle 1
E:01039 L:01179
DEC
INC
___________ _____
___________ _____
Cycle 10
E:01039 L:01179
Charge /
dischrge
cycle
Charged-in
capacity
Discharged
capacity
___________ _____
___________ _____NiCd-Man. 010:43
1,50 01735 23,45TEST
Measurement process
The charger repeatedly measures the battery during the char-
ge process. During the measurement phases the screen dis-
plays the message “TEST” in place of the charge current.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner Ultramat 17 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner Ultramat 17 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner Ultramat 17

Graupner Ultramat 17 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info