467070
19
Zoom out
Zoom in
Previous page
1/33
Next page
3736
Button click / buzzer settings
The purpose of this sub-menu is to adjust the settings for the audible sounder.
Button click: Every time you press a button you will hear a “click” sound to confirm your action. This
sound can be switched on (EIN) or off (AUS).
Buzzer: When the screen displays a warning, “completed” or an error message etc., the inte-
gral buzzer sounds at the same time to alert you. In this program point you can select
buzzer off (AUS), or the length (10 sec. or no time limt) of the audible warning.
Erase user settings
This menu provides the means to reset all the user settings
to their standard default values:
Initial power-on program : NiCd Automatik
NiCd Delta Peak : 20 mV / cell
NiMH Delta Peak : 15 mV / cell
Charge termination delay : 3 min
Safety timer : 120 min
Initial power-on current : 2.5 A (NiCd, NiMH, PB)
Car battery low voltage : 11.8 V
Button click : ON
Buzzer setting : 10 sec.
___________ _____
___________ _____
Clear
User Settings
___________ _____
___________ _____
Clear
***erased***
+
DEC
INC
___________ _____
___________ _____
Buzzer
OFF
___________ _____
___________ _____
Buzzer
no time limit
___________ _____
___________ _____
Buzzer
off after 10sec.
DECINC
DECINC
DECINC
___________ _____
___________ _____
button click
ON
___________ _____
___________ _____
button click
OFF
DECINC
ENTER
Car battery low voltage cut-off
If the charger is connected to a car battery which is not
required to start a car engine at the end of the session, then
it is safe to discharge it to a lower level.
The charger allows you to set an alternative value of 10.5 V,
which enables you to exploit the maximum capacity of the car
battery without deep-discharging it excessively.
The unit does
not store the alternative setting, so you must
reset it (if required) every time you start using the charger.
___________ _____
___________ _____
low voltage
cut off.= 11.8V
___________ _____
___________ _____
low voltage
cut off.= 10.5V
DECINC
NiCd / NiMH charge termination delay
At the start of the charge process the unit initiates a delay time
which suppresses automatic charge termination during this
(delay) period.
This means: during this delay period the charge
voltage is
not monitored, and the battery is charged for at
least the set length of time! The charge termination delay is
only effective n the NiCd and NiMH charge programs.
Initial power-on current (NiCd, NiMH, Pb)
You can select the charge / discharge current which is to be
set automatically when the charger is connected to the car
battery. In this program segment the value can be set sepa-
rately for each of the charge programs (NiCd, NiMH, LiIo,
LiPo, Pb).
___________ _____
___________ _____
charge cut-off
delay time =3min
DEC
INC
+
-
NiCd / NiMH safety timer
The value you set for the safety timer must be generous enough to allow a full charge of the battery.
As a practical guide we recommend a time which is about 30% longer than the expected charge
period; naturally, this varies according to the charge current you have set. Example: 1.8 Ah battery,
charge current 3.6 A -> charge time = 1.8 Ah / 3.6 A - 0.5 hours = 30 min +30% = safety timer =
40 min.
Warning: if you connect an already fully charged battery with the purpose of topping it up, it will be
charged for at least the delay time you have selected, and could then get very hot.
Caution - explosion hazard!
___________ _____
___________ _____
NiCd start curr.
2.5A
DEC
INC
+
-
This is particularly useful if you always
use the same charge current, as it avoids
the necessity to select the value sepa-
rately each time you use the charger.
In any case we recommend that you set
a “starting point” value of 2.5 A, as this
avoids the need to run through the enti-
re range every time you start using the
charger.
NiCd start curr.
3.7A
NiMH start curr.
3.7A
Lithium-Start
1.2A
Pb start curr.
1.2A
ENTER
Maximum Automatic current
In this program the charger detects the types of battery
connected and adjusts the charge current accordingly, to
avoid overcharging the pack.
The maximum charge current can be set using the INC /
DEC buttons
before you connect the battery to be
charged.
The charge process is terminated according to the values
set by the user for „NiCd Delta-Peak Termination Voltage“,
„Charge Termination Delay“ and „Safety Timer“.
___________ _____
___________ _____
NiCd max. curr.
automatic: 2.5A
DECINC
+
-
___________ _____
___________ _____
safety timer
120 min.
DECINC
+
-
When you start a charge process, the integral safety timer
automatically starts running at the same time. The safety
timer is designed to prevent catastrophic overcharging of
the battery on charge if the pack proves to be faulty, or if the
“battery full” detection circuit malfunctions.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner Ultramat 17 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner Ultramat 17 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner Ultramat 17

Graupner Ultramat 17 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info