637232

Graupner ULTRA TRIO PLUS 16 - 6469 Manual

37
Zoom out
Zoom in
Previous page
1/107
Next page
37
NiCd conditioning program
INC
This program is designed to optimise the capacity of a battery,
and balance the state of its component cells.At top right you
can set use the INC or DEC buttons to determine whether the
conditioning program is to start with a charge or discharge
cycle. After this you set the number of cycles from 1 to 5 (e.g.,
if you set three cycles, the pack will be charged and discharged
three times). The program discharges the battery using the set
discharge current stated on the right of the screen (0.1 ... 5.0
A), and then recharges it using the charge current (0.1 ...10.0
A) shown on the left of the screen. The charge process is ter-
minated automatically in accordance with the values already
set for „Ni-Cd Delta Peak cut-off voltage“. The discharge cut-off
voltage is set in the Ni-Cd discharge program. The method of
reading out the values for the actual cycle is described in the
section „Screen displays“.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i C d c y c l e C > D 1
DEC
ENTER
DEC
DEC
INC
or
ENTER
NiCd discharge balancing program
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i C d B L C
= 1 . 2 0 V / C
DEC
INC
+
-
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2 sec.
START
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
* * I N F O R M A T I O N * * *
B A L A N C E R C O N .
The discharge balancing program does discharge and balance
up to 8 cells of a battery pack.
The fi nal discharge voltage for the balancer can be set within
the range 1.20 … 1.30 V using the INC or DEC button.
The individual cells in a battery should be balanced before
the pack is charged, to avoid the possibility of individual cells
being overcharged during the charge process. A battery should
always be balanced before being charged if it has been stored
for a considerable period;
connect the balancer plug to the charger to carry this out.
It is also essential that the voltage of each cell in the pack should
be higher than the set balancer fi nal discharge voltage.
If you wish to obtain maximum battery capacity, the individual
cells should be discharged to 1.20 V a few hours - but no longer
than two hours - before the next charge process. If the voltage
falls below 1.20 V, the battery cells lose capacity, so the pack
must be charged to around 60% capacity before being stored
for a protracted period.
The program discharges the battery pack at a rate of 0.1 A
… 5.0 A. Cells with a higher cell voltage are discharged at an
additional current of around 100 mA (balancing current). The
charger terminates the discharge balance process once all
the cells have reached the balancer fi nal discharge voltage
(+0.01 V).
D C H
E N D 2 8 : 3 0 0 1 4 2 5
2 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i C d b a l a n c e c u t
INC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DEC
INC
+
-
DEC
INC
+
-
ENTER
N
C-C : 2 . 5 A
D
: 1 . 0 A
ENTER
2 sec.
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner ULTRA TRIO PLUS 16 - 6469 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner ULTRA TRIO PLUS 16 - 6469 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info