637232

Graupner ULTRA TRIO PLUS 16 - 6469 Manual

39
Zoom out
Zoom in
Previous page
1/107
Next page
39
INC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DEC
DEC
INC
ENTER
NiMh discharge program
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N M - D :
1 . 0 A 4 . 8 V
DECINC
+
-
DEC
INC
+
-
ENTER
NiMh conditioning program
The typical purpose of this program is to determine the residual
capacity of a transmitter, receiver or drive battery, or to discharge
the pack to a defi ned level.
In this program the charger discharges the pack using the set
discharge current (0.1 ... 5.0 A, left of screen) until its voltage falls
to the set fi nal discharge voltage (0.1 ... 16.8 V, right of screen).
The set fi nal discharge voltage should be a value of around
1.0 ... 1.2 V per cell, in order to avoid the pack becoming deep-
discharged. Deep-discharging a pack runs the risk of reversing
individual cells, i.e. they exhibit reversed polarity.
This program is designed to optimise the capacity of a battery,
and balance the state of its cells.
At top right you can use the INC or DEC button to determine
whether the conditioning program is to start with a charge or
discharge cycle. After this you set the number of cycles from 1
to 5 (e.g., if you set three cycles, the pack will be charged and
discharged three times). The program dis-charges the battery
using the set discharge current stated on the right of the screen
(0.1 ... 5.0 A), and then recharges it using the charge current (0.1
... 10.0 A) shown on the left of the screen. The charge process is
terminated automatically in accordance with the values already
set for „Ni-MH Delta Peak cut-off voltage“. The discharge cut-
off voltage is set in the Ni-MH discharge program. The method
of reading out the values for the actual cycle is described in the
section „Screen displays“.
or
N i M H c y c l e C > D 1
NiMh manual program
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i M h - M a n
C : 2 . 5 A
DECINC
+
-
Select this program when you simply wish to recharge a battery
using the set charge current. You can adjust the charge current
using the INC / DEC buttons, but only before you connect the
pack for charging. The range available is 0.1 A to 10 A.
Never use a maximum charge current higher as the value
described in the battery instruction, never higher as 2C!
Never charge transmitter batteries with more as 2 A!
f. e. a 4.2Ah battery should be limited to max. 4.2 A.
The charge process is terminated automatically in accordance
with the values already set for „Ni-MH Delta Peak cut-off
voltage“.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i M h d i s c h a r g e
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
DEC
INC
+
-
DEC
INC
+
-
N M - C
: 2 . 5 A
D
: 1 . 0 A
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i M h m a n u a l
2 sec.
2 sec.
ENTER
ENTER
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner ULTRA TRIO PLUS 16 - 6469 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner ULTRA TRIO PLUS 16 - 6469 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info