Manual Graupner MX12 (page 70 of 144) (English, German, French)

30127

Zoom out

Zoom in

1/144

Go to Throttle cut

Go to Ele Flp

Mx menu

Change selection

Change value/Select

switch

Reset selection to

Default (Adjust to

0% or ALWAYS ON)

Accessing the Aileron to Rudder Mixing Function

1. Place the transmitter power switch in the ON positi-

on.

2. Access the Function mode. To do so, press the

Down and Select keys simultaneously. Press

either the Up or Down key until AILRUD MIX

appears in the center portion of your LCD.

3. Press the (+) or (-) key to increase or decrease the

amount of rudder to be mixed with aileron. If you

want to reverse the Rudder Mix direction, press the

Clear key, bringing the mixing value to the factory

default (0%), and increase the value using the oppo-

site key (+) ir (-) from the key originally selected.

4. Press the Select key to access the switch assign-

ment function.

5. Press the (+) or (-) key to select the desired switch/

function to activate the Aileron-to-Rudder Mixing

function.

6. Access the ELEFLP MX mixing function by pres-

sing the Down key.

7. Access the THRO CUT function by pressing the Up

key.

8. Exit the AILRUD MIX function by pressing the

Down and Select keys simultaneously.

22 Function mode AIRPLANE

Function mode AIRPLANE

Throttle Cut switch; Flap System

Throttle Cut switch

This function assigns the Throttle Cut switch to the push

button located on upper right front of the transmitter.

The Throttle Cut function is designed to return the

throttle trim to the lowest position instantly and keep this

position while the button is pressed. This feature is used

to “cut“ or stop the engine without changing the position

of digital throttle trim.

Throttle cut operating position

(-32~-128)

Go to Flap System

Go to AilRud

Mix menu

Change value

Set function to

Inhibit

Accessing the Throttle Cut Function

1. Place the transmitter power switch on the ON positi-

on.

2. Access the Function mode. To do so, press the

Down and Select keys simultaneously. Press

either the Up or Down key, until THRO CUT

appears in the upper portion of the LCD screen.

3. Use the (+) and (-) keys to change the value of the

Throttle cut function.

Note: Pressing the Clear key will Inhibit the Throttle

Cut, turning it off until it has been reactivated.

4. Access the FLAP SYSTEM mixing function by pres-

sing the Down key.

5. Access the AILRUD MIX function by pressing the

Up key.

6. Exit the THRO CUT function by pressing the Down

and Select keys simultaneously.

Flap System

The Flap System function provides elevator compensa-

tion to counteract any pitch tendencies when flaps are

deployed.

SW Position

LANDING: (Flap SW forward side)

Elevator Offset value

Travel value (DN200~0~UP200)

Flap operating value Travel value

(DN125%~0%~UP125%)

Change value

Reset to selection

to Default

Go to Differential

Go to Throttle Cut

Change selection

Accessing the Flap System Function

1. Place the transmitter switch in the ON position.

2. Press the Down and Select keys simultanously to

enter the Function mode.

3. Press either the Up or Down key until FLAP SYS-

TEM appears in the top of the LCD.

4. Press the Select key to select the desired channels

to be adjusted.

5. Use the (+) or (-) keys to set the desired landing

mode surface positions.

6. Access the THRO CUT mixing function by pressing

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English, German, French as an attachment in your email.

The manual is 15,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English - 48 pages

Graupner MX12 User Manual - Dutch - 47 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MX12 Manual

Product: