Manual Graupner MX12 (page 69 of 144) (English, German, French)

30127

Zoom out

Zoom in

1/144

highlighted.

5. Move the appropriate control stick (lever, switch,

etc.) to the right or left of center to the direction of

travel you want to adjust. An arrow to the left of the

travel adjust value will reflect the current position to

be adjusted.

6. After the control stick or switch is placed in the

direction of travel to be adjusted, press the (+) or

(-) key until the proper amount of servo travel is

shown on the LCD. Press the (+) key to increase the

amount of servo travel. Press the (-) key to decrease

the amount of servo travel.

7. Follow the same procedure for the remaining chan-

nels.

8. Access the SUB TRIM function by pressing the

Down key.

9. Access the ELE F MX function by pressing the

Up key.

10. Exit the TRAVEL ADJ function by pressing the

Down and Select keys simultaneously.

Elevator to flap mixing

When this system is active and a value of flaps is input,

the flaps will be deflected each time the elevator stick is

used. The actual flap movement is adjustable for both

up and down elevator. A switch can be assigned to turn

the elevator to flap mixing on or off.

MIXING VALUE (+/- 125%)

Elevator Operating Direction

E-DN: Down side

E-UP: Up side

Mixing SW Selection

SW Display

ALWAYS ON: Always Mixing In

RIGHT FWD: Gear SW Forward

side On

RIGHT REA: Gear SW Rear

sideOn

LEFT FWD: FLAP SW Forward sideOn

LEFT REA: FLAP SW Rear sideOn

AILE D/R: AILE D/R SW Position 1On

ELEV D/R: ELEV D/R SW Position 1On

Go to Ail

Rud Mix menu

Go to Travel

Adjust menu

Change selection

Change value/Select

switch

Reset selection to

Default (adjust to 0%

or ALWAYS ON)

Accessing the Elevator to Flap Function

1. Place the transmitter power switch on the ON positi-

on.

2. Access the Function mode. To do so, press the

Down and Select keys simultaneously.

3. Move the elevator stick in the direction you want to

mix with flaps.

Note: The position indicator will reflect this change by

highlighting the up or down arrow.

4. Press the (+) or (-) key to increase or decrease the

amount of flaps to be mixed. If you want to reverse

the flap travel, press the Clear key, bringing the

mixing value to the factory default (0%), and increa-

se the value using the opposite key (+) or (-) from

the key originally selected.

5. Once you have adjusted the first mixing position (up

or down), place the elevator stick in the opposite

direction and follow Step 5 above to adjust the

second elevator mixing value.

6. Access the switch position by pressing the Select

key. Use the (+) or (-) keys to select from the one of

six switches, or from always on.

7. Access the TRAVEL ADJ function by pressing the

Up key.

8. Access the AIL RUD MIX Mixing function by pres-

sing the Up key.

9. Exit the ELE F MX function by pressing the

Down

and Channel keys simultaneously.

Aileron to rudder mixing

This form of mixing is designed so that when input to the

aileron stick is given, the rudder servo will also move,

eliminating the need to coordinate these controls manu-

ally. When adjusting, if an opposite mixing direction of

the rudder servo is required, simply press the (+) or (-)

keys to change the mixing value from a (+) or (-). This

will reverse the mixing direction of the rudder from its

original direction. The switch used to activate this mix

can also be selected as explained below. The factory

default is a value of 0%

Function mode AIRPLANE

Elevator to flap mixing; Aileron to rudder mixing

MIXING VALUE (+/- 125%)

Mixing SW Selection

SW Display

ALWAYS ON: Always Mixing In

RIGHT FWD: Gear SW Forward side On

RIGHT REA: Gear SW Rear sideOn

LEFT FWD: FLAP SW Rear sideOn

LEFT REA: FLAP SW Rear sideOn

AILE D/R: AILE D/R SW Position 1On

ELEV D/R: ELEV D/R SW Position 1On

Function mode AIRPLANE 21

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English, German, French as an attachment in your email.

The manual is 15,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English - 48 pages

Graupner MX12 User Manual - Dutch - 47 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MX12 Manual

Product: