467107
133
Zoom out
Zoom in
Previous page
1/200
Next page
133
Program description: servo position
Servo display
Use the arrow buttons of the left or right-hand touch-key
to leaf through to the Servo display menu point of the
multi-function menu:
mod.mem.
servo set.
D/R expo
wing mixer
base sett.
contr set.
phase trim
free mixer
basic sett
fail-safe telemetry
servo disp
Open the menu point by touching the central SET button
of the right-hand touch-key.
However, this visual display of the current servo posi-
tions can be called up not only by selecting this menu,
but also directly by simultaneously pressing the buttons
 of the left-hand touch-key from the transmitter’s
basic display, and also from almost any menu position.
Touching the central ESC button of the left-hand touch-
key returns you to your starting point again.
1
3
5
7
2
4
6
8
0%
0%
0%
–100%
0%
0%
0%
+100%
The current position of any servo is displayed in bar-
chart form, which takes into account the transmitter con-
trol and servo settings, the Dual-Rate / Expo functions,
the interaction of all active mixers etc., within the range
-150% to +150% of normal travel. 0% corresponds
exactly to the servo centre position. The servo display
provides a quick method of checking your settings, with-
out having to switch on the receiving system. However,
this does not relieve you of the need to check all your
programming steps carefully on the model before oper-
ating it for the first time, as this is the only safe method
of excluding possible programming errors.
The display is based on the following scheme for
fixed-wing models:
Bar 1 = throttle / brake servo
Bar 2 = aileron or left aileron
Bar 3 = elevator
Bar 4 = rudder
Bar 5 = right aileron
Bar 6 = (left) flap / free channel
Bar 7 = right flap / free channel
Bar 8 = free channel / second elevator servo
and for model helicopters:
Bar 1 = collective pitch or roll (2) or pitch-axis (2) ser-
vo
Bar 2 = roll (1) servo
Bar 3 = pitch-axis (1) servo
Bar 4 = tail rotor servo (gyro)
Bar 5 = pitch-axis (2) servo / free channel
Bar 6 = throttle servo or speed controller
Bar 7 = gyro gain / free channel
Bar 8 = speed governor / free channel
Note:
Please note, however, that the servo display always •
applies to the original servo sequence, i.e. it takes
no account of any outputs swapped over in the “Re-
ceiver output” menu of the Basic model settings
menu, nor changes made directly at the receiver us-
ing the Telemetry” menu.
The number of channels shown in this menu corre-•
sponds to the eight control channels available at the
mx-16 HoTT transmitter. However, the actual number
of channels you can use varies according to the type
of receiver in the model, and to the number of servos
connected to the receiver; the number may therefore
be much smaller.
Use this display during the model programming pro-•
cedure, so that you can immediately check all the
settings at the transmitter. However, this does not re-
lease you from the responsibility to check all the pro-
gramming steps on the model itself before operating
it for the first time, in order to exclude the possibili-
ty of errors!
133


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info