467107
131
Zoom out
Zoom in
Previous page
1/200
Next page
131
Program description: free mixers
* NN = Nomen Nominandum (name to be stated)
MIX1 6 el
trv
+20%
+20%
0%offs
S TO
SEL
Asymmetrical mixer ratios
For many applications it is necessary to set up different
mixer values on either side of the mixer neutral point.
Start by resetting the offset of the mixer used in our
example (“6 el”) to 0%, as shown in the picture
above. Now use the arrow button of the left or right-
hand touch-key to select the ASY field, and then touch
the central SET button of the right-hand touch-key. If
you now turn the rotary proportional control CTRL 7 -
assigned in our example to input 6 - in the appropriate
direction, the mixer ratio for each direction of control can
be set separately, i. e. to left and right of the selected
offset point using the arrow buttons of the right-hand
touch-key:
MIX1 6 el
trv
+20%
0%offs
SYM
ASY
+55%
Note:
If you are setting up a switch channel mixer of the “S
NN *” type, you must operate the assigned switch to
achieve this effect. The vertical line then jumps between
the left and right sides.
Examples:
The switch SW 2 has already been assigned to con-1.
trol channel 8 in the Transmitter control settings
menu, in order to open and close the aero-tow re-
lease.
I5
I6
I7
+
trv
100%
100%
100%
100%
100%
100%
2
+ +
+ +
+
+
I8
100%
100%
+ +
ctrl 7
free
free
In the meantime you have carried out a few aero-tow
flights, which showed that you always needed to hold
in slight up-elevator during the tow. You now wish to
set the elevator servo (connected to receiver output
3) to slight “up” trim when the tow release is closed.
In the screen display familiar from page 127 we have
set up the third linear mixer to accomplish this, using
the switch channel “S” as the mixer input. Now move
the selected switch to the OFF position, and move to
the …
typ fro
to
M1
M2
M3
c1
el
C1
6
el
el
S
1
2
… mixer set-up page.
Use the arrow button of the left or right-hand
touch-key to select the “Offs” line, then touch the cen-
tral SET button of the right-hand touch-key.
According to the travel setting selected in the “Trans-
mitter control settings menu and the switch posi-
tion, the offset value now jumps to +X% or -X%, e. g.:
MIX3 S el
trv
0%
0%
+100%offs
SET
S TO
Use the arrow button of the left or right-hand
touch-key to move to the “Travel” line, then touch the
central SET button of the right-hand touch-key. After
moving the selected switch to the mixer ON position,
set the required mixer ratio in the now highlighted
value fields using the arrow buttons of the right-hand
touch-key.
MIX3 S
el
trv
+100%offs
ASY
SYM
+10%
+10%
The following example applies to model helicopters:2.
In the Helicopter program you may wish to assign
one of the rotary proportional controls (CTRL 6 … 8)
to the collective pitch trim function. This is the pro-
cedure: in the “Transmitter control settings menu
assign one of these two transmitter controls to input
“E8”. Now simply define a free mixer “8 1” with a
symmetrical mixer ratio of, say, 25%. Due to the inter-
nal coupling, this transmitter control now acts equally
on all the collective pitch servos you are using, with-
out affecting the throttle servo.
131


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info