467107

Graupner MX-16 HoTT Manual

87
Zoom out
Zoom in
Previous page
1/200
Next page
87
Program description: base settings - model helicopter
Note:
A count-down timer is indicated in the basic display by
a flashing colon (:) between the minutes field and the
seconds field.
Phase 2 / Phase 3
You will automatically be in the “normal” flight phase 1
unless you have already assigned a switch to phases 2
or 3.
Both the number and name of this flight phase are fixed
permanently as “normal”, and cannot be changed. For
this reason the “normal” phase is simply concealed, i. e.
it is not displayed as phase 1.
10:01 G3
phase 2
phase 3
hover
speed
–––
–––
rotor direct right
pitch min
rear
timer
It is also important to understand that the flight phases
have their own inherent priorities which need to be ob-
served, particularly when assigning individual switches.
The underlying scheme can be described as follows:
If all assigned flight phase switches are closed or •
open, the “normal” flight phase is active.
If only one switch is closed, then the flight phase as-•
signed to the currently closed switch is active.
If two switches are closed, then the flight phase with •
the lower number is active.
For example, this would be phase 2 if the switches
assigned to phase 2 and 3 are closed.
The “auto-rotation phase” ALWAYS has precedence •
over all other flight phases, regardless of the priori-
Auto-rotation
10:01 G3
phase 2
phase 3
hover
speed
–––
pitch min
rear
timer
5
4
autorotat.
The name “Auto-rotation” is permanently assigned to
Phase 4, and CANNOT be altered. The only available
option is to assign a switch to it using the switch symbol
at the right of the screen.
For more information on programming flight phases
please refer to the “Helicopter mixers” section starting
on page 114.
Receiver output
For maximum flexibility in terms of receiver socket
assignment, the mx-16 HoTT software provides the
means to swap over the servo outputs 1 to max. 8;
this is carried out on the second page of the “Receiver
output” sub-menu.
10:01 G3
phase 2
phase 3
hover
speed
timer
5
4
autorotat.
2
receiv out
Touch the central SET button of the right-hand touch-key
to move to the next page of the display. Here you can
assign the “control channels” for servos 1 … 8 to any
receiver output you wish to use. However, please note
that the display in “Servo display” - which you can ac-
ties outlined above. When the auto-rotation phase
is selected, the switch is always made WITHOUT
DELAY.
With this in mind, you may wish to take the inherent •
phase priorities into account when assigning names
to the flight phases; see below.
At the servo end the transition does not occur •
“abruptly”, but with a fixed transition period of about
one second.
Programming
When you select “Phase 2” or “Phase 3” using the arrow
buttons  of the left or right-hand touch-key, the
“Name” field for that flight phase is already framed.
If the default name does not seem appropriate, touch
the central SET button of the right-hand touch-key, and
the current setting is shown highlighted. Now use the
arrow buttons of the right-hand touch-key to select an
appropriate name from those available. Touch the SET
button to conclude the input process.
Now press the button of the left or right-hand touch-
key to move to the right-hand column at the bottom of
the screen, indicated by the switch symbol
, and
briefly touch the central SET button. You can now assign
a switch to the phase as described on page 57. We
recommend one of the two three-position switches SW
4/5 or SW 6/7, in each case starting from the centre
toggle position.
For more information on flight phase programming
please refer to page 114, in the section entitled “Flight
phase specific settings for collective pitch, throttle and
tail rotor”.
… 87 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info