467107
86
Zoom out
Zoom in
Previous page
1/200
Next page
86
Program description: base settings - model helicopter
timer
Two timers are shown in the basic display: one stop-
watch and one flight timer.
STARLET
#02
0:00h
stop
flt
0:00
0:00
0.0V
5.6V
HoTT
M
A physical switch or a control switch - e. g. the control
switch G3 located on the throttle limiter - can be as-
signed to these two timers in the “Timers” line …
rotor direct
swashplate
right
3sv(2rol)
cut off
–125%
+100%
1
pitch min
rear
timer 0:00 –––
… using the switch symbol at the bottom right-hand
side of the screen. The assigned switch starts both tim-
ers, and also halts the stopwatch.
The method of assigning a physical switch or a control
switch is described on page 57.
The flight timer, and the saving of telemetry data on a
memory card inserted in the card slot (see page 23)
always starts simultaneously with the stopwatch, but
continues to run even when the stopwatch is halted
(switched off). It can only be stopped by touching the
central ESC button of the left-hand touch-key with the
stopwatch halted.
Once stopped, both timers can be reset to the initial
value by simultaneously touching the  buttons of
the right-hand touch-key (CLEAR).
Switching between “count-up” and “count-down”
Count-up timer (stopwatch function)
If you assign a switch and start the stopwatch with the
initial value of “0:00”, the timer runs up until the maxi-
mum of 180 minutes and 59 seconds, then re-starts at
0:00.
Count-down timer (timer function)
In the left-hand minutes field you can select a starting
time within the range 0 to 180 minutes; in the right-hand
seconds field the range is 0 to 59 seconds. Any combi-
nation of times can also be selected.
Simultaneously pressing the  buttons of the right-
hand touch-key (CLEAR) resets any settings you have
entered to “0” or “00”.
rotor direct
swashplate
right
3sv(2rol)
cut off
–125%
+100%
1
pitch min
rear
timer 10:01
G3
Procedure
Select the desired input field using the arrow buttons 1.
 of the left or right-hand touch-key.
Touch 2. SET in the centre of the right-hand touch-key.
Select the required time in the highlighted minutes 3.
and seconds fields using the arrow buttons of the
right-hand touch-key.
Touch the central 4. SET button to conclude the input
process.
Switch back to the basic display by repeatedly touch-5.
ing the central ESC button of the left-hand touch-key.
With the stopwatch halted, press the  buttons of
the right-hand touch-key simultaneously (CLEAR) to
switch the stopwatch to the “Timer” function; see top
right in the next illustration:
STARLET
#02
0:00h
stop
flt
10:01
0:00
0.0V
5.6V
HoTT
M
If you now operate the assigned switch, the stopwatch
starts from the set initial value, counting down (“Timer
function”). When the set time has elapsed, the timer
does not stop, but continues to run to allow you to read
off the time elapsed after reaching zero. To make this
clear, the over-run time is shown highlighted (black
background).
Sequence of sounds
30 sec. before zero: triple beep
single beep every two seconds
20 sec. before zero: double beep
single beep every two seconds
10 sec. before zero: single beep
single beep every second
5 sec. before zero: single beep every second at higher
rate
zero: longer beep; display switches to
inverse video
The “alarm timer” is reset by simultaneously pressing
the  or  buttons of the right-hand touch-key
(CLEAR) after you have halted the timer.
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info