467107
50
Zoom out
Zoom in
Previous page
1/200
Next page
50
Backing up receiver settings
The “Receiver Setup” segment of the program
“Firmware_Upgrade_grStudio” can be used to save all
the data programmed in the receiver in a file on your
computer, so that you can transfer the data set back into
the receiver in an emergency; this eliminates the need to
re-program the receiver using the “Telemetry menu, as
would otherwise be necessary.
We recommend that you call up the “Receiver Setup”
program from the “Firmware_Upgrade_grStudio” pro-
gram. Alternatively you can start the application directly.
You will find the file “Receiver_Setup.exe” in the “Graup-
ner_PC-Software” folder.
Note:
If you call up “Receiver Setup” from the Firmware_Up-
grade program, ensure that the sub-program “Re-
ceiver_Setup.exe” is located in the same folder as
the “Firmware_Upgrade_grStudio” program; see the
screen-shot above!
For this program you need the USB interface, Order No.
7168.6, and the interface lead, Order No. 7168.S, sup-
plied in the mx-16 radio control set, Order No. 33116.
Backing up receiver settings
Connecting the receiver to the PC1.
With the receiver switched off, connect the USB in-
terface, Order No. 7168.6, to the socket marked “-+T”
on the receiver using the adapter lead, Order No.
7168.6S.
Backing up receiver settings
The connector system is polarised: note the small
chamfers on the edges. Do not use force under any
circumstances; the plugs should engage easily.
Adapter lead
Order No. 7168.6A
If a central red wire is present,
cut through it
Caution:
If you are using the - earlier - adapter lead, Order
No. 7168.6A, and this is fitted with a three-core
lead, cut through the central red wire of the
adapter lead before using it.
Now connect the USB interface to the PC or lap-
top using the USB lead supplied in the set (PC-USB
/ mini-USB). If connected correctly, a red LED on the
interface circuit board should light up.
The receiver should be left switched off at this point.
Receiver Setup: selecting the port2.
Start the program “Firmware_Upgrade_grStudio_
Ver-X.X.exe” by double-clicking on it, as described
for updating the transmitter software (see page 41).
(Version 1.9, which is current at the time this manu-
al went to press, starts without being installed before-
hand.)
Open the “Controller Menu” and click on “Receiver
Setup” in the “Upgrade / Link” folder. Alternatively se-
lect the “Receiver Setup” entry under “Menu”.
A program window now appears, in which you should
start by setting the “correct” COM port for the USB in-
terface, Order No. 7168.6. If you are not sure of this,
check the COM port in the “Port select” window in
the “Controller Menu” (see earlier), and note the Com
port number at the entry “Silicon Labs CP210x USB
to UART Bridge”. In accordance with the previous up-
date descriptions this would be the port “COM 3”.
(If you select the wrong port, the program will alert
you to the error.)
Reading out receiver data3.
Click on the “Connect” button and wait until the Sta-
tus bar below it starts to advance:
Locate the SET button on the receiver and hold it
pressed in while you switch it on. After about three
seconds the receiver’s current values will be dis-
played in the corresponding fields. If the progress bar
is “faster than you are”, and reaches the end before
you have switched the receiver on, the pop-up win-
dow shown here appears. In this case repeat the pro-
cedure.
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info