467111

Graupner MC 32 HOTT Manual

98
Zoom out
Zoom in
Previous page
1/345
Next page
98 Program description - Base setup models | Helicopter models
RECEIVER CHANNEL MAP BIND1
Rx Input Ch 1
Rx Input Ch 2
Rx Input Ch 3
Rx Input Ch 4
Rx Output Ch 1
Rx Output Ch 2
Rx Output Ch 3
Rx Output Ch 4
After selection of the desired output with the selec-
tion keys of the left or right touch pad, the appropriate
value fi eld will be framed. Briefl y tap on the centre
SET key of the right touch pad. The current setting
will be displayed in inverse video. Now use the selec-
tion keys of the right touch pad to select the desired
input channel’s respective transmitter output, see
page 234.
BUT CAUTION:
If you wish to operate two servos with one
control function, for example such as trans-
mitter control function 2 (roll) which is divided
up into control channels 1 & 2 for left and right roll
servos for the "3Sv(2Roll)" option in the »Heli type«
menu; then "map" the corresponding transmitter
outputs, in this case for channels 1 & 2 (= inputs to
the receiver) accordingly.
The number of lines available in the list
(outputs) corresponds to the maximum
number of servos which can be attached to
the given receiver.
• If you see the warning …
CAN‘T
RECEIVE
DATA
OK
… then there is no bound receiver within range.
If the case may be, switch the RF module or/and
your receiving system on.
• With the »Tx. output swap« option, available
on the mc-32 transmitter, see page 234, the
transmitter’s control functions can be interchanged
in any way; it is also possible to assign multiple
outputs to one and the same control function. In
the interests of clarity however we strongly advise
that you use only one of these two options.
Channel assignment on other receivers
As already mentioned, the “Rcv Ch map” menu option
can be used to freely distribute the mc-32 HoTT
transmitter’s 16 control channels across up to four
receivers, whereby the numbering of outputs (servo
connections) as well as the maximum number of
available lines (outputs) will correspond to the maxi-
mum number of servo connections available on the
given receiver.
RECEIVER CHANNEL MAP BIND2
Rx Input Ch 16
Rx Input Ch 16
Rx Input Ch 16
Rx Input Ch 16
Rx Output Ch 1
Rx Output Ch 2
Rx Output Ch 3
Rx Output Ch 4
After selection of the desired output with the selection
keys of the left or right touch pad, the respective input
fi eld will be framed.
Tap the centre SET key of the right touch pad. The
current setting will be displayed in inverse video. Now
select the desired input channel with the selection
keys of the right touch pad. For example, suitable to
the above rudder example.
RECEIVER CHANNEL MAP BIND2
Rx Input Ch 4
Rx Input Ch 4
Rx Input Ch 4
Rx Input Ch 4
Rx Output Ch 1
Rx Output Ch 2
Rx Output Ch 3
Rx Output Ch 4
Note:
The number of lines available in the list
(outputs) corresponds to the maximum
number of servos which can be attached to
the given receiver.
RF transmit
This menu line provides an option for manually
switching the transmitter’s RF transmission on and
off to specifi c models while the transmitter is in op-
eration. For example, to save power while a model is
being programmed.
If this line option was set to OFF, it will be
canceled (i. e. set to ON) the next time the
transmitter is switched on.
If necessary, use the  selection keys of the left
or right touch pad to move into the “RF transmit” line
then activate the option with a brief tap on the centre
SET button of the right touch pad.
… 98 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info