747993
51
Zoom out
Zoom in
Previous page
1/80
Next page
51 / 80
33028_mc_28_Teil2_jh
D.red (Differentiation reduction)
If you use the aileron differentiation, the aileron effect is strongly
affected by the deflection of the ailerons. Justification: a further
excursion of the one aileron is almost impossble and the control sur-
face moving downward does not reach the "normal" position.
In order to restore this reduced aileron effect, the "differentiation
reduction" reduces the degree of the aileron differentiation.
A 0% value means that the "aileron differentiation" programmed in
the transmitter is held. A value equal to the set percentage of the
aileron differentiation means is completely removed in maximum
butterfly function (with flaps completely out). In case of a reduction
value bigger than the set aileron differentiation will be removed
completely before the full deflection of the flap control stick.
Elevator curve (Brake -> Elevator)
If the flaps extend through the brake control as described previously
in the "Brake settings" menu, the speed of a model is often adversely
affected. The exteded flaps usually produce a tail or nose moment,
the model will react gaining or loosing altitude.
With this mixer, the potential tail or nose moment can be avoided by
a correction value mixed on the elevator. Push the SET button, then
change to the manu page of the 6-point curve mixer "Brake -> ELE".
Programming
The offset you set in the line "Brake offset" of the menu "Model
type" has an effect on this mixer:
When the set offset value is exceeded, the green, vertical bar in the
graphic display, indicating the position of the brake control, moves
away from the edge of the graph. The brake flap control travel auto-
matically respreads to 100%, as described in the "Model type" menu.
The neutral point of the mixer always lies at the left edge of the
graph, independent of the set offset.
Now adjust the Elevator curve in the direction of the opposite end
end points. Set this 6-point curve mixer according to the same prin-
ciple described for the curve mixer in the "Throttle curve" menu.
AI curve
Brake settings
AI
Butt
D.red
0%
0%
0%
0%
0%
0%
FL FL2
Normal
AI curve
Brake settings
Butt
D.red
0%
0%
0%
0%
0%
0%
Normal
Input
Output
Point ?
–100%
0%
0%
Brake
normal
Ele
Curve off
Normal
Input
Output
Point 1
–19%
–6%
–7%
Brake
Normal
Ele
Curve on
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info