747993

Graupner MC-28 4D Manual

49
Zoom out
Zoom in
Previous page
1/80
Next page
49 / 80
33028_mc_28_Teil2_jh
ELE -> FLAP (ELEVATOR -> FLAP)
To support the elevator, the flap function can be influenced by the
elevator control in a phase-specific manner with this mixer. Select
the mixing directionto move the flaps downward when the elevator
is pulled ("up"), and conversely upward when the elevator is pushed
("down"). A symmetrical or an asymmetrical effect can be defined
for each flap pair. Set the respective control in the middle or the
respective side. Values of ±150% are possible. With a switch assigned
in the next line "ELE -> FLAP Offset", the deployment of the flaps from
the elevator and the range of the deployment can be switched off
and on and also set.
ELE -> FLAP Offset (symmetrical elevator Offset)
In the previously described line "ELE -> FLAP", you have entered a
value to support the elevator. In this line "HR -> WK Offset", you
determine the "application point" of the proportionate entrainment
of the flaps from the elevator through the offset value. The flaps are
entrained from the elevator from the neutral position of the elevator
control stick with the percentage set in the line "ELE -> FLAP" and
with an offset value of 0%, .
With an offset value not equal to 0%, the flaps are only entrained
from the specified offset point in the direction "low" and in the direc-
tion "high" during a movement of the elevator control stick.
To adjust the offset point, bring the elevator control stick to the
desired position in one of the two possible directions. Tap the SET
button to store this position, regardless of the current position of the
elevator trim. Push the SET button in the center position of the ele-
vator control to set the offset value back to 0%, regardless of the cur-
rent position of the elevator trim.
The deployment of the flaps from the elevator can be switched off
and on with a switch assigned in the “Switch” column. Assigning a
switch is described in the section "Control and switch assignment".
FL
0%
0%
FL pos.
EL FL 0%0%
0%
AI
Normal
Diff. 0%
FL
0%
0%
FL pos.
EL FL 0%0%
0%
STO
Normal
EL FL Off. 0% –––
… 49 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info