747993
31
Zoom out
Zoom in
Previous page
1/80
Next page
31 / 80
33028_mc_28_Teil2_jh
"- Trv +"
Move the marking frame with the selection buttons over the "Off-
set" column to the right side to reach this column.
This column sets the control travel for both sides, together or sepa-
rated for each side. The setting range is 0 to 150% of the normal con-
trol travel. The set values always refer to the settings in the column
"Centre". Perform a symmetrical or asymmetrical setting as described
in the "Offset" section.
"– Time +"
Move the marking frame with the selection buttons over the "Trv"
column to the right side to reach this column.
In this column, a time delay is set for the respective channel. The set
seconds indicate the time that elapses between the switching states.
If the encoder or switch is actuated, the switching process then runs
in the set time. Assign a symmetrical or asymmetrical setting as
described in the "Offset" section.
Dual Rate / Expo
In this menu you can set the options Dual Rate and Expo.
Dual Rate
This option reduces the travel of each control function. This reduc-
tion can be activated through a switch. If no switch is assigned, the
reduction will be always active. The graphical representation to the
right shows the control path profile for the selected control function.
Setting the Dual Rate step-by-step:
Select the line of the desired control function
Assign the switch in the column (process as described in the
section "Control settings")
Input the reduction value in the column SEL
Now you can use the selected switch to pass from reduced control
travel to full control travel.
If the function has to be assigned specifically to the phase, the
related phase must be active. The phase name will be shown in the
second line from the bottom of the display.
In5
– trv +
+100%
+100%
+100%
+100%
In6
In7
In8
+100%
+100%
+100%
+100%
Normal
In5
– time +
0.0s
0.0s
0.0s
0.0s
In6
In7
In8
0.0s
0.0s
0.0s
0.0s
Normal
Servo adjustment
Stick mode
Channel 1 curve
Switch display
Control adjust
Dual Rate / Expo
100%
100%
100%
Ail
Ele
Rud
DUAL
–––
–––
–––
SEL
Servo travel
Servo travel
Servo travel
Control travel
Control travel Control travel
Dual Rate = 100%
Dual Rate = 50% Dual Rate = 20%
Servo travel
Servo travel
Servo travel
Control travel
Control travel
Control travel
Dual Rate = 100%
Dual Rate = 50%
Dual Rate = 20%
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info