747993
32
Zoom out
Zoom in
Previous page
1/80
Next page
32 / 80 33028_mc_28_Teil2_jh
Expo
Move the marking frame with the selection buttons over the
"SEL" column to the right side to reach the column. "EXPO" instead
of "DUAL" will be shown.
This function influences the travel of each control function. You can
set an exponential curve. The graphical representation to the right
shows the control path profile for the selected control function.
This function can also be activated through an assignable switch.
Setting the Expo step-by-step:
Select the line of the desired control function
Assign the switch in the column (process as described in the
section "Control settings")
Input the Expo curve value in the column SEL
Now you can use the selected switch to pass from linear control
travel to exponential control travel.
Combining Dual Rate and Expo
If you have set Dual Rate and Expo to act simultaneously, the travels
will overlap. You will experience a reduced, exponential course of
the control travel.
Asymmetrical setting of Dual Rate and/or Expo
To set an asymmetrical travel of the control function, assign a control
switch (see the "Transmitter switch" menu). The Dual Rate or Expo
functions only affect one side of the control travel.
Throttle curve
This menu allows you to change the control characteristics of the
control function 1. The control function acts directly on the servo
connected to control channel 1 or via several mixers to several ser-
vos. Settings in this menu affect the throttle / brake control function
for an airplane model and the throttle / pitch function for a helicop-
ter model.
If the function has to be assigned specifically to the phase, the
related phase must be active. In the last line of the display will be
shown the phase name.
+33%
0%
0%
Ail
Ele
Rud
EXPO
3
–––
–––
SEL
Normal
Servoweg
Servoweg
Servoweg
Geberweg Geberweg Geberweg
Expo = +100% Expo = +50% Expo = –100%
Servoweg
Servoweg
Servoweg
Geberweg
Geberweg
Geberweg
Expo = +100%
Expo = +50%
Expo = –100%
Servo adjustment
Stick mode
Switch display
Control adjust
Dual Rate / Expo
Channel 1 curve
Input
Output
Point ?
0%
0%
0%
Ch1
Normal
curve
Curve off
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info