747993
28
Zoom out
Zoom in
Previous page
1/80
Next page
28 / 80 33028_mc_28_Teil2_jh
Column 1
The first column lists the control outputs.
The numbered servos refer to the servos connected to the corre-
sponding receiver outputs, assuming that the transmitter and
receiver outputs have not been switched. A change in the control
mode does not influence the numbering of the servos.
Column 2 "Rev"
This option controls the servo direction to the specifics of each
model.
Select with the SET button and t u: "=>" normal, "<=" reverse
Column 3 "Cent"
You can set the servo centre in a ±125 % area within the servo travel
of max. ±150 %. The servo is always adjusted independently of all
other trim and mix settings.
Column 4 "– Trv +"
In this column you can set the servo travel for both sides, together
or separate for each side. The setting range is 0 to150% of the nor-
mal travel. The set values always refer to the settings in the column
"Centre".
Symmetrical travel setting:
Move the related control element (control stick, proportional con-
trol or switch) into a position in which both sides of the travel adjust-
ment are surrounded by the marking frame.
Asymmetrical travel setting:
Move the related control element (control stick, proportional con-
trol or switch) into a position in which the single side of the travel
adjustment is surrounded by the marking frame.
Column 5 "Lim"
In this column you can limit the servo travel. To reach the column "-
lim +", move the marking frame with the selection button to the
right over the column "- Trv +".
Symmetrical or asymmetrical setting of the limit as explained in the
"– Trv +" section.
S1
S2
S3
Rev cent +
trv
0%
0%
0%
100% 100%
100% 100%
100% 100%
0%
0%
100% 100%
100% 100%
S4
S5
S
e
r
v
o
t
r
a
v
e
l
C
e
n
t
r
e
a
d
j
u
s
t
m
e
n
t
S1
S2
S3
Rev cent +
lim
0%
0%
0%
150% 150%
150% 150%
150% 150%
0%
0%
150% 150%
150% 150%
S4
S5
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info