747993
27
Zoom out
Zoom in
Previous page
1/80
Next page
27 / 80
33028_mc_28_Teil2_jh
Ailerons/Flaps
In this line you can select the number of servos installed in the wings.
The following table shows the control channels to which the servos
must be connected.
Control surfaces
count
Occupied control channel
1AILE 2
1AILE 1FLAP 2 | 6
2AILE 2 + 5
2AILE 1FLAP 2 + 5 | 6
2AILE 2FLAP 2 + 5 | 6 + 7
2AILE 4FLAP 2 + 5 | 6 + 7 / 9 + 10
4AILE 2FLAP 2 + 5 / 11 + 12 | 6 + 7
4AILE 4FLAP 2 + 5 / 11 + 12 | 6 + 7 / 9 +
10
According to this scheme, the required mixers and the respective
setting possibilities are activated in the "Wing mix" menu.
Brake offset
This line sets the offset point in which the control surfaces (AILE/
FLAP) are completely retracted or closed.
The function will be assigned to the related input in the right column.
Assign an Offset_point:
Move the control element of the input CH1-control stick, input 1,7,8
or 9, in the position where the control surfaces have to be retracted
or closed. Tap on the SET button to save the "Offset" point.
A “+” extends the flaps for brake offset values when the correspond-
ing control element is moved from front to rear toward the pilot.
A “-” extends the flaps for brake offset values when the correspond-
ing control element is moved from back to front away from the pilot.
Servo adjustment
In this menu the servo parameters are set for each servo: servo
direction, neutral point, servo travel and limits. Start the servo set-
tings in the left column.
Tail type
Motor at C1
normal
None
Aile/flaps 1AIL
Model type
Brake Off In1+100%
SEL
Tail type
Motor at C1
normal
None
Aile/flaps 1AIL
Model type
Brake Off In1+90%
SELSTO
Suppress models
Base setup model
Control adjust
Model type
Servo adjustment
Stick mode
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info