747932
25
Zoom out
Zoom in
Previous page
1/51
Next page
25 / 52
S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh
Some transmiers allow the correcve factors to be altered
during a flight using the proporonal controls, whereas others
allow fixed values only.
It is possible to use a channel to control the factor value by set-
ng up flight phase specific transmier control sengs, but
only with some transmiers; please see the instrucons sup-
plied with your transmier and refer to the Transmier control
sengs” and “Flight phase sengs”.
Programming example for transmiers with proporonal controls
Gyro setting
MODE RU (2)C7
Aile: (2)C9
Elev: (2)C8
MODE AI/EL (2)C7
Rudd: 6
Factor: (44%)C10
If your HoTT transmier is equipped with proporonal controls, it is
also possible to adjust the value for each axis during a flight: what
you might call ‘flying the sengs. You need to assign proporonal
controls to any channel in the range 5 to 16. Now you can alter the
value using these controls. The current value is shown in brackets.
Procedure, using the ailerons as an example step-by-step
1. Assign a free proporonal control to a free control channel in the
transmier's control setup menu.
2. In the transmier's telemetry menu, switch to the "Gyro seng"
display page of the receiver menus.
3. Move the cursor to the desired line, for example to the "Ailerons"
line for the aileron.
4. Press the SET key to acvate the value field.
5. Select the channel prepared according to point 1.
6. Save it by pressing the SET buon again.
7. Move the selected proporonal control to check.
If the value displayed in the bracket changes between 0 and 10,
then programming is OK. Otherwise, the relevant sengs should
be chec
ked and corrected if necessary.
8. The opons "elevator" and "rudder" may have to be set the same.
Notes
In flight, the values are to be changed successively unl the
desired gyro correcon is achieved without swinging up.
Possibly, it makes more sense and the evaluaon easier, to ac-
vate first one axis of the gyro and to fly the atude.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-18 in the language / languages: English as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner GR-18

Graupner GR-18 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info