747932
23
Zoom out
Zoom in
Previous page
1/51
Next page
23 / 52
S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh
Buerfly mixer with elevator addion
FREE MIXER
FROM CHANNEL: 1
TRIM: +0%
TRAVEL–: +100%
MIXER 1
TRAVEL+: +100%
TO CHANNEL: 2
FREE MIXER
FROM CHANNEL: 1
TRIM: +0%
TRAVEL–: +100%
MIXER 2
TRAVEL+: +100%
TO CHANNEL: 5
FREE MIXER
FROM CHANNEL: 1
TRIM: +0%
TRAVEL–: +10%
MIXER 3
TRAVEL+: +10%
TO CHANNEL: 3
Notes
These mixers may only be needed on transmiers without trans-
mier-side buerfly mixers.
The respecve travel seng must be adapted to the model and
made so that the servos never stall mechanically.
Display "Gyro seng"
Preparaon step-by-step
1. With deacvated gyroscope, carefully trim the model on one or
more trim flights on the transmier side.
2. Switch the receiver off and on again to transfer the own trim
state to the memory of the receiver.
3. Enable gyro control as described below.
4. Set the factor for gyro correcon, eventually check the values for
the single control surfaces.
MODE
Gyro setting
MODE RU 0
Aile: 5
Elev: 5
MODE AI/EL 0
Rudd: 5
Factor: OFF
The mode can be set separately for AILE/ELEV and RUDD.
The mode can be set permanently or it can be switched through an
assignable control channel. If a proporonal control is assigned to
the selected control channel in the transmier, the respecve mode
can be acvated in the following seng ranges of the maximum pos-
sible servo travel:
Mode Range
0 (no regulaon) –150 % –75 %
1 (normal regulaon) –75 % … –25%
2 (Heading Lock mode with suppress.)
(In sck center posion Heading-Lock
acts. Outside the sck neutral posion
the gyro control is acve.)
–25 % +25 %
3 (Rate mode)
(In the sck neutral posion Hea-
ding-Lock acts over the enre control
area)
+25 % +150 %
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-18 in the language / languages: English as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner GR-18

Graupner GR-18 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info