747932
26
Zoom out
Zoom in
Previous page
1/51
Next page
26 / 52
S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh
Programming example for transmiers WITHOUT proporonal controls
Procedure, using the ailerons as an example step-by-step
1. In the transmier's telemetry menu, switch to the "Gyro seng"
display page of the receiver menus.
2. Select the desired mode in the two "Mode" lines.
3. Move the cursor to the desired line, for example to the "Ailerons"
line for the aileron.
4. Press the SET key to acvate the value field.
5. Select the desired value (1 -10 or OFF).
6. Save it by pressing the SET buon again.
Start with a lower value (clues see secon Factor) and make
a test flight. If the gyroscope correcon is too low, increase
the value step by step to the desired correcon. If the model
already oscillates, reduce the value step by step.
7. The opons "elevator" and "rudder" may have to be set the same.
8. Leave or reset the "Factor" seng to "OFF".
Notes
The values are eventually to be changed successively unl the
desired gyro correcon is achieved without swinging up.
Possibly, it makes more sense and the evaluaon easier, to ac-
vate first one axis of the gyro and to fly the atude.
Display "Axis assignment"
Before starng the sengs on a new model, enter the number of
aileron servos in the "Aileron servo" line and then assign and set the
gyro axes and direcons using the "Do setup" opon described
below.
Aileron servos
Gyro setting
Do setup NO
Aile (Right) +0
Elev (Push) +0
Aile servos 1
Rudd (Right) +0
The number of aileron servos must be specified in this line.
If 2 aileron servos are specified, the control channel (servo) 2 gyro-
scope also acts on the receiver output (servo) 5. In addion, the sum
of both channels is used for gyro suppression if the ailerons are addi-
onally used, for example, as Flaperon or Speedbrake.
Notes
Always specify the correct number of aileron servos in the trans-
mier. If there are more than two, however, then the receiv-
er-side gyro stabilizaon only aects the servos connected to
receiver output 2 and 5.
Gyro setting
MODE RU 1
Aile: 2
Elev: 4
MODE AI/EL 4
Rudd: 6
Factor: OFF
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-18 in the language / languages: English as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner GR-18

Graupner GR-18 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info