747935
15
Zoom out
Zoom in
Previous page
1/24
Next page
15- 24
GR-18_3D_jh_V1
Optional: If the motor off area is not desired in Attitude mode
then you can reduce the lower servo travel to -70%. Thus the
reduction has no effect on the rate mode, program the reduc-
tion through a switchable free mixers. In this mixer the reduc-
tion is active only in Attitude mode. (see display screenshot on
the left)
Oneshot
Oneshot is a quick communication protocol between receiver
and speed controller and should only be activated if the speed
controllers allow this function. It allows the speed controllers to
communicate much faster with receiver. So the motors react
faster to receiver controls. The motor output signal is now
shorter, about 125µs-250µs, instead of before PWM (1000µs –
2000µs).
Minpower%
The setting is principally used to prevent the motors shut down
in flight. Adjust so that the motors are running straight. Under no
circumstances unnecessarily high set, this would limit the con-
troller possibilities.
Logging
Value 1 is the general attitude control, rest as needed
logs the corresponding servo to SD card for later evaluation and
error analysis.
Settable values:
0 = No logging, Telemetry display of Euler and yaw angle
1 = roll and nick logging
We recommend always logging at least one function.
CALIBR. POSITION
With Calibr. Position the acceleration sensors can be calibrated
so that in attitude mode with stick and trim neutral, the copter
is precisely horizontally aligned. For this purpose, it is simply
placed on absolute level surface and set the value to Yes. After
a moment, it jumps back to No and the calibration is done.
Do
not forget to store disabling the field!
MIX 2
TRV -30% 0%
Os
ASY
SYM
CH1 CH1
0%
MIX 2
TRV -30% 0%
Os
ASY
SYM
CH1 CH1
0%
Optional mixer for reduction of
throttle curve in attitude mode
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-18 - S1019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-18 - S1019 in the language / languages: English as an attachment in your email.

The manual is 9,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner GR-18 - S1019

Graupner GR-18 - S1019 User Manual - German - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info