747931
35
Zoom out
Zoom in
Previous page
1/51
Next page
35 / 52
S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh
Display "Tail rotor seng"
Tail sensivity
Tail rotor settin
Direktanteil R +115
Direktanteil N +115
Tail sensitivity 65
Tail rate +85
Tail expo +40
The "Tail sensivity" opon allows you to adjust the sensivity either
by specifying xed values or alternavely by assigning a control chan-
nel (C5 ... C16) that controls the value from the transmier with a
proporonal control. To do this, a rotary or slider control is assigned
to one of the control channels 5 ... 16 and the remaining sengs are
le at the default values. In the value field of the "Tail sensivity"
line, the corresponding channel is then merely to be selected instead
of a xed value. The current control posion is displayed in the
bracket in front, for example "(50) C10", see lower figure under "SWP
sensivity".
Via corresponding sengs in the transmier, a flight-phase-depen-
dent sensivity control is also possible.
The max. tail sensivity is rst determined
at the highest rotor speed
and it should be own individually for each speed. It can be increased
unl the tail begins to swing up. Aerwards, the tail sensivity has
to be reduced a lile, unl in all flight posions no swinging of the
tail is recognizable anymore.
Adjustment range: 1 … 100, MIN or C5 … C16
Note
If a control channel is selected in the "Tail sensivity" line, but no
channel is assigned to it on the transmier side, the value in brack-
ets corresponds to the current neutral posion of this control chan-
nel.
Tail rate
Sets the max. potenal rate of rotaon in Rate mode for the tail.
Adjustment range: +50 … +120
EXPO tail
Servo travel
Servo travel
Servo travel
Control travel
Control travel
Control travel
Expo = +100%
Expo = +50%
Expo = –100%
In this line an exponenal curve for the control of the tail rotor can
be set.
With a seng of "0" a linear control of the tail rotor takes place, with
high percentage values a progressive control is achieved, whereby
the helicopter does not react so sensive around the middle of the
sck.
Adjustment range: 0 … +50
Note
Expo sengs should always be made either in the receiver or in the
transmier, otherwise the two Expo sengs overlap.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner Falcon 12 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner Falcon 12 plus in the language / languages: English as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner Falcon 12 plus

Graupner Falcon 12 plus User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info