590777
27
Zoom out
Zoom in
Previous page
1/96
Next page
GMC-I Messtechnik GmbH 27
8.1 Measurements with Suppression of RCD Tripping
8.1.1 Measurement with Positive Half-Waves
(only MTECH+/MXTRA/SECULIFE IP)
Measurement by means of half-waves plus direct current makes it
possible to measure loop impedance in systems which are
equipped with RCCBs.
For DC measurement with half-waves you can choose between
two alternatives:
DC-L: lower premagnetization current allowing for faster mea-
surement
DC-H: higher premagnetization current, therefore higher protec-
tion against tripping of RCD
Select Measuring Function
Set Parameters
* Parameters used for report generation only which do not influence the measurement
Sine (full wave) Setting for electric circuits without RCD
15 mA sinusoidal Setting only for motor protection switch
with low nominal current
DC+half-wave Setting for electric circuits with RCD
Start Measurement
Semiautomatic
Measurement
8.2 Evaluation of Measured Values
The maximum allowable
loop impedance Z
L-PE
which may be displayed
after allowance has
been made for maxi-
mum operating mea-
surement error (under
normal measuring con-
ditions) can be deter-
mined with the help of
Table 1 on page 88.
Intermediate values can
be interpolated.
The maximum allowable
nominal current for the
protective device (fuse
or circuit breaker) for a line voltage of 230 V after allowance has
been made for maximum measuring error can be determined with
the help of Table 6 on page 89 based upon measured short-cir-
cuit current (corresponds to DIN VDE 0100 Part 600).
Special Case: Suppressing Display of the Limit Value
The limit value cannot be
ascertained. The inspec-
tor is prompted to evalu-
ate the measured val-
ues himself, and to
acknowledge or reject
them with the help of the
softkeys.
Measurement passed:
key 4
Measurement failed:
X key
Z
L-PE
Tripping characteristics:
Diameter*: 1.5 to 70 sq. mm
Cable types*: NY...- H07...
Number of wires*: 2 to 10-strand
Nominal current:
2 ... 160 A, 9999 A
A, B/L, C/G, D, E, H, K, GL/GG & Factor
Sine
15 mA sinusoidal
Waveform:
DC-L offset and positive half-wave
Contact voltage:
DC-H offset and positive half-wave
2-pole
Measurement with country-specific
plug insert (e.g. Schuko)
Note
Selecting test probe and Lx-PE
reference or AUTO is only relevant for
report generation.
Semiautomatic measurement
See also section 5.8 regarding the
AUTO parameter.
Polarity selection
measurement
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt PROFITEST MXTRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt PROFITEST MXTRA in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt PROFITEST MXTRA

Gossen Metrawatt PROFITEST MXTRA User Manual - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info