656011
8
Zoom out
Zoom in
Previous page
1/13
Next page
- 32 -
Setting the Transmitter
group’s setting turns to the maximum(1/1) or the minimum(Min.). If the current group
is in the TTL mode, all the other groups which are in the M mode will change their
FEC amount simultaneously. The FEC amount is changeable from -3 to 3 in 0.3 stop
increments, until one of the group’s setting turns to the maximum(3) or the minimum(-
3). If the current group is in the -- mode (flash off), the amounts will not change.
4. Short press the <GR> Button again to confirm the setting.
Test Flash
1. Press the <TEST> Trigger Button to see the
whether flash will fire normally or not.
2. Fully press the <TEST> Trigger Button, and
the Status Indicator Lamp turns red and the
flash can be triggered.
3. The settings on the transmitter end will
synchronize to the receiver end at the same
time.
Modeling Lamp Control
Double-click the <CH/OK> Button to power ON/OFF the modeling lamp.
Setting the Transmitter
Automatically Enter Power Saving Mode
1. The flash trigger will go into standby mode after the transmitter enter sleep mode, and
the displays on the LCD panel will disappear.
2. Press any of the button (<TEST> fully pressed/<CH/OK>/<GR>/<MODE>) can wake
up the flash trigger. If the transmitter is attached to the CANON EOS camera, half
press the shutter can also wake up the system.
3. If the transmitter is set to single contact mode( isdisplayed), the system will not
enter power saving mode.
The following table lists the available and unavailable custom functions of this flash.
Note: Some icons will be displayed when setting the relevant custom functions to make users
have a good understanding.
Functions
Synchronization
delay setting
Single contact
mode
Custom
Functions No.
C.Fn-00
C.Fn-01
Settings and Description
OFF
Master flash synchronization delay N*100 us
(synchronization delay icon is displayed.)
OFF
ON (The single contact mode set icon is displayed.)
It is advisable to set the transmitter to single contact
mode when using it to trigger the flash by PC cord or
through camera's single contact.
Setting Signs
00
1~100
--
on
C.Fn: Setting Custom Functions
- 31 -
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox X1TS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox X1TS in the language / languages: English as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info