656038
7
Zoom out
Zoom in
Previous page
1/9
Next page
11
12
TTL
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
Second-Curtain Sync
0.5 0.7
1
1.5
2
3
4
6 9
13
18
1.7
2.3
4
5
7
10 15 20
30
40 60
m
ft
Zoom
mm
35
• Set the camera to Rear
mode and press the shutter
button halfway, then the flash
display panel will show the
second curtain sync icon
< >.
• When the camera is not set
to Rear mode, pressing the
shutter button halfway will
not light up the icon < >
on the flash display panel.
This flash unit supports slave triggering mode. To enter S1/S2
mode from the master mode, press < > button and hold for
seconds, then S1 or S2 will be shown on the LCD display. Setting
as S1 mode, press < > button will enter S2 mode. Setting as
S2 mode, press < > button can back to master mode, then
S1 or S2 will disappear from the LCD panel.
The flash output setting in slave triggering mode is the same as
that in manual mode. After pressing the <SET> button, the flash
output blinks. Press the < - > button or < + > button to set a value.
S1 Slave Triggering Mode
In this mode, the flash unit can function as a slave flash for
S1/S2 Slave Triggering Mode
• Second-curtain sync works well in the camera' s "buLb" mode.
• With i-TTL, two flashes will be fired even at slow shutter speeds.
The first flash is only the preflash, and not a malfunction.
• Stroboscopic flash cannot be set.
C.Fn: Setting Custom Functions
The following table lists the available and unavailable custom
functions of this flash. The icon “ indicates the flash custom function
is supported but “0” indicates the custom function is not supported.
Custom
Functions No.
C.Fn-00
C.Fn-01
C.Fn-02
C.Fn-03
C.Fn-04
Setting No.
0
1
0
1
0
1
0
1
0
1
Settings &
Description
Enabled
Disabled
Enabled
Disabled
60 minutes
30 minutes
Within 8 hours
Within 1 hour
1/32
Full output
Function
Auto power off
AF assist
Slave auto
power off timer
Slave auto
power off cancel
Test firing with
autoflash
Support
or Not
0
0
C.Fn Custom Functions
1. Press < > button for 2 seconds or longer until < Fn > is
displayed.
2. Select the Custom Function No.
• Press the <-> or <+> button to set the Custom Function No.
3. Change the setting.
• Press< SET > button and the Setting blinks.
• Press the <-> or <+> button to set the desired setting. Pressing
< SET> button will confirm the settings.
• After you set the Custom Function and press < MODE > button to
exit the Custom Function setting, the camera will be ready to
shoot.
Maximum Stroboscopic Flashes
Hz
1 Hz
2 Hz
3 Hz
4 Hz
5 Hz
6 Hz
7 Hz
8 Hz
9 Hz
10 Hz
20 Hz
30 Hz
40 Hz
50 Hz
60 Hz
70 Hz
80 Hz
90 Hz
1/4
6
5
4
4
3
3
3
3
2
2
1/8
14
12
10
8
6
6
5
5
4
4
1/128
90
90
80
70
56
44
36
32
28
24
1/64
90
90
80
70
56
44
36
32
28
24
1/32
60
60
50
40
32
28
24
22
20
12
1/16
30
30
20
20
20
20
10
10
8
8
Flash Output
• S1 or S2 mode is not supported in the following cases: when
“red-eye reduction” function is started by the master flash (either
camera pop-up flash or external on-camera flash); and when the
master flash uses the modeling flash function.
• In S1 or S2 mode, the flash output level is only manually
adjustable.
• In S1 or S2 mode, TTL flash or Multi flash is not available.
• Setting as S1/S2 slave triggering mode and attaching to the
camera, the flash will change to master mode and be set as TTL
mode automatically when pressing the shutter button halfway.
creating multiple lighting effects. It is respectively applicable to
manual flash environment. In S1 mode, the flash unit will fire
synchronously when the master flash fires, the same effect as that
by the use of radio triggers.
S2 Slave Triggering Mode
This mode is also called “Preflash Cancel”, similar to S1 mode. In
this mode, the flash unit will ignore a single “preflash” from the
master flash and will only fire in response to the second, actual
flash from the master. Therefore, this flash unit is applicable when
using a TTL master flash.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox TT680 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox TT680 N in the language / languages: English as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info