656038
6
Zoom out
Zoom in
Previous page
1/9
Next page
M: Manual Flash
The flash output is adjustable from 1/1 full power to 1/128th power in
1/3rd step increments.
Use a hand-held flash meter to determine the required flash output
to obtain a correct flash exposure.
0.5 0.7
1
1.5
2
3
4
6 9
13
18
1.7
2.3
4
5
7
10 15 20
30
40 60
m
ft
Zoom
mm F
35
56
1. Press the <MODE> button
so that the <M> is displayed.
2. Set the flash output.
• Press the <SET> button.
• The flash output blinks.
• Press the < - > button to set a
lower value. Or press the <+>
button to set a higher value.
• Press the <SET> button again
to lock the settings.
• Press the shutter button
halfway to see the effective
flash range displayed.
1
/
128
Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
0.5 0.7
1
1.5
2
3
4
6 9
13
18
1.7
2.3
4
5
7
10 15 20
30
40 60
m
ft
Zoom
mm
35
1. Press the <MODE> button
so that <Multi> is displayed.
2. Select the item to be set.
• Press the <SET> button to
select the item (blinks).
1
/
16
Multi
Hz
1
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
Number of flashes / Firing frequency = Shutter speed
For example, if the number of flashes is 10 and the firing frequency
is 5 Hz, the shutter speed should be at least 2 sec.
To avoid overheating and deteriorating the flash head, do not use
stroboscopic flash more than 10 times in succession. After 10
times, allow the camera flash to rest for at least 15 min. If you try
to use the stroboscopic flash mode more than 10 times in
succession, the firing might stop automatically to protect the flash
head. If this happens, allow the camera flash to rest for at least
15 min.
• Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
• Using a tripod, a remote switch, and external power source is
recommended.
A flash output of 1/1 or 1/2 cannot be set for stroboscopic flash.
• Stroboscopic flash can be used with "buLb".
10 10
3. Set the desired number.
• Press the <-> button to set a
lower value. Or press the
<+> button to set a higher
value. Then press the <SET>
button. The next item to be
set starts blinking.
After you set the flash output
and press the <SET> button,
all the settings will be
displayed.
0.5 0.7
1
1.5
2
3
4
6 9
13
18
1.7
2.3
4
5
7
10 15 20
30
40 60
m
ft
Zoom
mm
35
1
/
128
Multi
Hz
Range of flash output:
1/4<->1/8<->1/16<->1/32<->1/64<->1/128
09
10
M
2
Flash Output
When you change the flash output during shooting, the following
table will make it easier to see how the stop changes such as 1/2-
0.31/2+0.3 when you increase or decrease the flash output.
For example, when you decrease the flash output to 1/2, 1/2-0.3,
or 1/2-0.7, and then increase the flash output to more than 1/2,
1/2+0.3, 1/2+0.7, and 1/1 will be displayed.
1/1
1/1–0.3
1/2+0.7
1/1-0.7
1/2+0.3
1/2-0.3
1/4+0.7
1/2-0.7
1/4+0.3
1/2 1/4
...
...
Figures displayed when reducing flash output level
Figures displayed when increasing flash output level
• If you set the flash coverage manually, make sure it covers the
lens focal length so that the picture will not have a dark
periphery.
• If you use a commercially-available sync cord to connect the
camera to the camera flash' PC terminal, set the flash zoom
manually.
Using the Wide Panel
Pull out the wide panel and place
it over the flash head as shown.
The flash coverage will then be
extended to 14 mm.
• The catchlight panel will come
out at the same time. Push the
catchlight panel back in.
• The <ZOOM> button will not
work.
• If you use bounce flash with the wide panel in place, the subject
will be illuminated by both the bounce flash and direct flash,
which will look unnatural.
• Pull out the wide panel gently. Using excessive force may
detach the wide panel.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox TT680 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox TT680 N in the language / languages: English as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info