656038
3
Zoom out
Zoom in
Previous page
1/9
Next page
Attaching to the Camera
1
Slip the camera flash’s
mounting foot into the camera’s
hot shoe all the way.
. Attach the Camera Flash.
2
Rotate the locking screw on the
mounting foot until it locks up.
. Secure the Camera Flash.
3
Rotate the locking screw on the
mounting foot until it is loosed.
. Detach the Camera Flash.
Turning on the Power Switch
1
. Set the power switch to <ON>.
Camera flash starts charging.
2. Check that the flash is ready.
The flash-ready indicator turns
red, indicating that the camera
flash is fully charged and ready
for firing.
Pressing <TEST> button will fire
a test flash.
About Auto Power Off
To save battery power, the power will be off automatically after a certain
period of idle use.
The flash will enter sleep mode after approx. 90 seconds of idle use
when being attached to the camera.
Setting as off camera mode, namely, the S1/S2 slave triggering mode,
the flash will enter sleep mode after approx. 60 minutes (adjustable, 30
minutes by default).
To turn on the camera flash again, press the camera’s shutter button
halfway. Or press the camera flash’s test firing button.
Fully Automatic Flash Shooting
When you set the camera's shooting mode to < P > (Program AE)
or < AUTO > (Full Auto), i-TTL fully automatic flash will make it as
easy as normal AE shooting in the < P > and < AUTO > modes.
Installing the Batteries--------------------------------------------------------03
Attaching to the Camera-----------------------------------------------------04
Turning on the Power Switch------------------------------------------------04
Fully Automatic Flash Shooting---------------------------------------------04
Using i-TTL Autoflash in the Shooting Modes---------------------------05
To avoid overheating and degrading the flash head, do not
fire more than 20 continuous flashes. After 20 continuous
flashes, allow a rest time of at least 10 min.
If you fire more than 20 continuous flashes and then fire
more flashes in short intervals, the inner overheating
prevention function may be activated to make the recycling
time about 8 to 20 sec. If this occurs, allow a rest time of
about 15 min, and the flash will then return to normal.
Cautions for firing continuous flashes
Installing the Batteries
Install four size-AA batteries.
1
Use your thumb to press the
battery compartment cover, and
then slide it to open the cover.
. Open the cover.
2. Install the batteries.
Make sure the + and battery
contacts are properly oriented
as shown in the compartment.
3. Close the cover.
Slide the battery compartment
cover as shown by the arrow to
close it.
Recycling Time and Flash Count (with size-AA alkaline batteries)
Recycling Time
Approx. 0.1-5 sec
Flash Count
Approx. 100-700
Based on new size-AA alkaline batteries.
Use a new set of four batteries of the same brand. When
replacing the batteries, replace all four at one time.
Size-AA Ni-MH or lithium batteries can also be used.
Getting Started and Basic Operation
03
04
If < > blinks on the LCD panel, the
battery power is low and the camera
flash stops charging. In this case, the
<ZOOM> button is disabled. Please
change the batteries immediately.
Using size-AA batteries other than the alkaline type may cause
improper battery contact due to the irregular shape of the battery
contacts.
If you change the batteries after firing many flashes continuously,
be aware that the batteries might be hot.
When the Power Switch is set to ON and the flash power is off
automatically after a certain period of idle use, power
consumption exists and long-time power discharge damages
batteries. Therefore, make sure to shut down the flash power by
setting the Power Switch to OFF if the flash is not used for long.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox TT680 N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox TT680 N in the language / languages: English as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info