Manual Giordani Citywave (page 22 of 44) (English, Dutch, French, Italian, Portuguese, Spanish)

769010

Zoom out

Zoom in

1/44

GIORDANI CITYWAVE MODULAR SYSTEM (FROM 0 TO 36 MONTHS APPROXIMATELY)

STROLLER

OPENING THE STROLLER

1. As shown in Fig. 1a, pull the folding handle

on both sides, following the direction of the

arrow. At the same time, pull the stroller han-

dle to expand the stroller frame. As shown

in Fig. 1b, push the pedal down completely

in order to lock the frame in position. Check

that the two tubes are fully connected as

shown in Fig. 1c to ensure that it is fully open.

WARNING: When the child is seated, never

pull the closure handle on both sides if the

frame is not locked into position.

ASSEMBLY OF WHEELS

2. As shown in Fig. 2a/2b, insert the front and rear

wheels in the specic housings and these will

be tted correctly only when you hear a “CLICK”.

WARNING: Before use, try moving and rotat-

ing the wheels manually to make sure that

they are all properly tted in their housings.

ASSEMBLY OF HOOD

3. As shown in Fig. 3a, open the seat in the direc-

tion of the arrow. As shown in Fig. 3b, insert the

hood frame in the specic housing on the seat.

It is fully fitted when you hear a “CLICK”. As

shown in Fig. 3c/3d, fasten the snap buttons

and fasten the seat and hood Velcro strap to

complete the assembly as shown in Fig. 3e.

ASSEMBLY AND REMOVAL OF SEAT

4. Assembly: As shown in Fig. 4a, open the seat

completely and insert both side ends in the

specic frame housings (align the arrow indi-

cating the insertion point with the frame rivet).

It is fully tted when you hear a “CLICK”. Be-

fore use, make sure the set is tted properly.

Removal: As shown in Fig. 4b, to release the

lock press the buttons under each armrest and

pull the seat out of the frame at the same time.

WARNING: before use, check that the seat is

correctly secured.

FITTING AND REMOVING THE FRONT SECURITY BAR

5. Assembly: As shown in Fig. 5a, insert the ends

of the safety bar into the appropriate slots on

both sides of the seat at the same time.

Removal: As shown in Fig. 5b, press the front

bar release buttons at the same time, then

remove it.

OPENING THE HOOD

6. As shown in Fig 6a, push outwards to fully open

the hood. The stroller will have been complete-

ly assembled when it looks like in Fig 6b.

WARNING: Failure to read these instructions

could compromise the child's safety, read

them carefully.

TURNED SEAT

7. As shown in Fig 7a, push down the same but-

ton that you would operate to detach the seat,

then remove it and turn it.

BACKREST ADJUSTMENT

8. As shown in Fig 8a, push the backrest adjust-

ment button to raise or lower it. (3 positions).

ADJUSTMENT OF THE LEG REST

9. As shown in Fig 9a/9b, push the leg support

adjustment buttons located underneath it to

raise or lower it, then proceed adjusting it.

WHEEL OPERATION

10. Use of the swivel wheels: as shown in Fig

10a, turn the wheel lock devices (to the left

and right of the wheels) outwards, thus al-

lowing the wheels turn. As shown in Fig 10b,

turn the wheel lock devices (to the left and

right of them) inwards and the wheels will

lock in a straight position. Quick removal of

the wheels: as shown in Fig. 10c, press the

release button and at the same time pull the

FRONT wheel, applying a minimum force.

As shown in Fig. 10d, press the release but-

ton and at the same time push the REAR

wheel out, applying a minimum force. Use

the locking device: as shown in Fig 10e, to

lock the rear wheels, press the locking de-

vice down with the foot. When the indicator

(d) turns RED, this means that the brake

is enabled. To unlock the wheels, push the

locking device down with your foot. When

the indicator (d) turns GREEN, this means

that the wheel brake has been disabled.

WARNING: Push the stroller back and forth

to make sure the brake has been correctly

enabled.

USING THE RETENTION BELTS

11. Fastening: first, insert the buckles connect-

ed to the retention straps of the child's

waist (C & D) in the corresponding hous-

ings connected to the shoulder straps, as

shown in Fig 11a. Then insert the E & F

parts in the central button G, as shown in

figure 11b. When a CLICK is heard, it will

be completely inserted. Unfastening: press

the central button (G) to remove (E & F).

Adjusting the safety strap: as shown in Fig

11c, tighten or loosen the belt for the child's

comfort. Adjust the height of the shoulder

retention belt: the position (H) is suitable

for children aged over 6 months. Position (I)

is suitable for children under 6 months. To

change the height, insert the shoulder re-

tention strap inside the belt cover and insert

the end inside the backrest. Next, secure

the shoulder strap to the desired height.

WARNING: Always check that the child re-

straint system is always tightly closed and

adjusted when using the stroller.

ACCESSORIES

ASSEMBLY AND REMOVAL OF THE ADAPTER

12. Assembly: As shown in Fig. 12a, insert the

two adapters inside the housings in the frame

structure. The assembly is considered correct-

ly carried out when it appears as in Fig. 12b.

Disassembly: As shown in Fig. 12c, press the

release buttons on the adapter and remove it.

ASSEMBLY AND REMOVAL OF THE CAR SEAT

13. Assembly: As shown in Fig. 13a, insert the

ends of the car seat into the housings in the

adapters mounted on the frame structure.

When you hear a CLICK, they will have been

completely inserted.

Disassembly: Depending on the type of re-

lease button available on the modular system,

choose the most suitable method. Method A:

as shown in Figure A, pull upwards the release

button "a" on the back of the car seat, then lift

the seat as shown in Fig. 13b.

Method B: as shown in Figure B, press the side

button "b" downwards and at the same time

push the button "c" upwards, then raise the

seat as shown in Fig. 13b.

ASSEMBLY AND DISASSEMBLY

OF THE CARRYCOT

14. Assembly: As shown in Fig. 14a, insert the

ends of the carrycot inside the housings lo-

cated in the adapter mounted on the modular

system structure. When you hear a CLICK,

they will have been completely inserted.

Disassembly: As shown in Fig. 14b, press the

release button located under the carrycot

and unhook it.

WARNING: choose the appropriate instructions

according to the carrycot purchased. Remove

the seat before installing the car seat.

HOW TO CLOSE THE MODULAR SYSTEM

15. As shown in Fig. 15a, fold the hood following

the direction indicated by the arrow. As

shown in Fig 15b/15c, press the backrest

adjustment button downwards and lower it

as far as possible. As shown in Fig. 15d, pull

the closing hook from both sides following

the direction indicated by the arrow. Then

push the handle downwards to unlock the

modular system frame. As shown in figure

15e, push the same pedal upwards with the

foot, which is used to fold the structure, so

that the structure will be released, then raise

the closure handle as shown in Fig. 15f. When

a CLICK is heard, the modular system will be

completely closed as shown in Fig. 15g.

CLEANING AND CARE

Clean and maintain the modular system regularly

to eliminate any danger of accidental injury to the

child. Clean the seat with a brush and the remain-

ing parts with soap or neutral detergent. Regularly

inspect the modular system to identify defects

such as loose screws, damaged parts or broken

seams. Provide for xing the defects if necessary.

To avoid damage to the modular system, read the

instructions carefully before installing it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Giordani Citywave in the language / languages: English, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Giordani Citywave Manual

Product: