479852

Gemini 7201 Manual

4
Zoom out
Zoom in
Previous page
1/9
Next page
ULTRASONIC MODULE DESCRIPTION
GEMINI ref. 5123.
The ultrasonic module ref. 5123 protects the vehicle, detecting the door opening or the movements
inside the passenger’s compartment.
FITTING INSTRUCTIONS.
Connect the ultrasonic module to the alarm system wiring harness then put the connectors of
the ultrasonic cells in the suitable socket: RED for the TX cell and WHITE for the RX cell.
SENSITIVITY ADJUSTMENT.
- Lower one of the front windows (approximately 20-cm).
- Adjust the ultrasonic sensor sensitivity to a minimum level.
- With the doors completely closed, arm the alarm pressing twice on the transmitter 2 button.
- Put one hand through the open window and move it. If the sensitivity is properly adjusted the
LED on the sensor lights. Otherwise, it is necessary to increase the sensitivity.
TECHNICAL DATA
Working Voltage 9÷16VDC
Current absorption 2,5 mA
Working temperature -30°C +85°C
DESCRIPTION OF THE MODULE GEMINI 7059.
GEMINI 7059 protects the vehicle detecting attempts to break into the passengers
compartment by the emission of an electromagnetic field (frequency = 2,45 GHz).
The working of the sensor is based on the reflection of the electromagnetic waves when a
object, made of a conductive material, is located on the field.
The measurement of the reflected waves can detect the intrusion and then trigger the alarm
device connected to the sensor.
GEMIN 7059 is insensitive to air movements (wind, thermal air drift, etc.), for this reason it’s
suitable to be fitted on pick-up vehicles, convertible cars and vehicle equipped by a sliding
sunroof.
Due to the fact that the insulating materials are transparent to the electromagnetic waves it’s
possible to fit the sensor module in a hidden position, e.g. under the passengers compartment
carpet.
FITTING INSTRUCTIONS.
In order to obtain the correct working of the sensor module it’s very important to identify the
best fitting position depending on the vehicle model.
In any case, it’s important to remember that, the complete protection of the vehicle internal
space can not be obtained using a high-frequency sensor module.
The sensitivity adjustment must be done in order to avoid false alarm triggering, due to
objects in movement outside the vehicle (e.g. people, other vehicles or motorbikes).
To increase the false alarms protection it’s important to comply the following fitting rules :
a) the connection cable of the sensor must be fitted and routed far from the module case.
b) the module must be fitted far from coin holders or glove compartments.
c) avoid all metal mobile objects in the passengers compartment.
To find the proper fitting position, please see the fitting diagram contained in this fitting
manual.
ELECTRIC CONNECTIONS.
The connection of the module to the alarm system is very easy as the wiring harness is
equipped with a proper connector.
SENSITIVITY ADJUSTMENT.
GEMINI 7059 is provided by a sensitivity adjustment control, by this it’s possible to set the
sensor sensitivity from a MINIMUM value (NOT ZERO) to a MAXIMUM value.
To help the adjustment operation the module is provided by a RED led located on the top side
of the sensor case. This led is lighted for 4 sec. when an alarm condition is detected. (NOTE :
between an alarm condition and the following is present a delay time of 5 sec.).
ADJUSTMENT PROCEDURE :
1) Set the adjustment control to the MAXIMUM value (clockwise direction).
2) Close all doors, windows, boot and bonnet, then arm the alarm unit connected to the
sensor module and wait for the end of the arming delay time, or set on the DIAGNOSTIC
MODE
3) Move the hands near the vehicle windows (lateral, front and rear) and make sure that the
sensor does not activate.
4) If the sensor activate reduce the value of the adjustment control (anti-clockwise
direction), then repeat the test described on the point 3).
5) If the test result is positive, (no false alarms detected moving the hands near the
windows), disarm the alarm unit and open one of the front windows.
6) Arm the alarm unit again, or set on the DIAGNOSTIC MODE, and check the correct
alarm triggering moving an arm inside the passengers compartment.
Pink
Brown
Green/Black
Ultrasonic module
White
connector
connector
TX
RX
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7201 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info