479852
2
Zoom out
Zoom in
Previous page
1/9
Next page
DESCRIPTION
The system Gemini 7201 is a compact alarm supplied with sensors and siren, which can be
installed on vehicles with 12Volt battery-negative to earth.
FUNCTIONS
GEMINI 7201.
- Compact alarm with dynamic code (Frequency 433.92 MHz ).
- Blinker and electronic siren.
- Negative control for supplementary siren.
- Electrical central door locking control (negative or positive) windows and electric sunroof (for
vehicles equipped with Pack-comfort system).
- Perimetric and volumetric protection (US and HF models).
- LED’s memory and wiring connections diagnosis.
- Remote controlled PANIC function.
He alarm systems are equipped with 2 codified transmitters (art. 7208E).
INSTALLATION INSTRUCTIONS (for the installer)
- To make universal the central door locking system it is necessary to use a 5056 module.
- Connect the power feed wire to the battery positive terminal and the earth directly to the
vehicle frame.
- Connect the alarm Green-Brown wire to the door pin-switch.
- Avoid routing connection wires next to interference sources (sparking plugs cables, high
voltage coil).
- The alarm must be installed in the engine compartment protected from water and with the
key lock switch turned to the top.
- If you install an ultrasonic module the ultrasonic heads must be positioned at the top of each
windscreen pillar and must be pointing at each opposite diagonal corner away from the facia
outlets.
DIP-SWITCHES PROGRAMMING TABLE
1 ON Current absorption sensor ON
1 OFF Current absorption sensor OFF
2 ON Closure control 6 seconds
2 OFF Closure control 1 second
3 ON Comfort control ON (25 seconds)
3 OFF Comfort control OFF
4 ON Diagnostics ON
4 OFF Diagnostics OFF (normal use)
5 ON
5 OFF
Do not use
6 ON Self-learning of a new active code
6 OFF Self-learning of a new excluded code (normal use)
ATTENTION : SET THE DIP-SWITCHES BEFORE TURNING THE EMERGENCY KEY TO ON.
FOLLOWING THE PRESENT RULES IT IS ADVISABLE TO SET THE DIP-SWITCH N. 1 TO OFF.
DIAGNOSTICS: (final check-up o f the installer or quick after sale checks).
The diagnostics function allows during the test or at the end of the installation to verify quickly the
correct working of the alarm system and the electrical connections of the vehicle plant.
DIAGNOSTICS INLET. With the emergency key to OFF, set the dip-switch N.4 to ON. The activation
of the diagnostics function is signalled by 4 acoustic/optical signalling while supplying the alarm
system. At the end of the signalling the module outlets (+A) and the engine immobilisation
activates; the LED lights fix.
In this condition it is possible to test each inlet and if the external connections and/or the internal
circuits of the device work correctly one audible tone or one-direction indicator lights flashing signal
each alarm triggering.
It is necessary to wait 1 second between each alarm input triggering. In the diagnostics modality
the transmitter 1 button does not work as arming/disarming button but it is used to verify the
transmitter’s working. An audible tone or one direction indicator lights flashing signals the correct
working.
The transmitter 2 button activates the Panic alarm. This modality allows testing the siren working
and the outlet of the additional siren with negative control.
To stop the Panic alarm it is necessary to press again on the button 2 of the transmitter (followed
by a neutral period of 5 seconds).
DIAGNOSTICS OUTLET.
1. Press on the transmitter 2 button to activate the panic function.
2. During the alarm signalling, pressing on the transmitter 1 button the system goes back to the
normal working.
ATTENTION! AT THE DIAGNOSTIC OUTLET SET THE DIP-SWITCH N.4 TO OFF.
WIRING CONNECTIONS
(disconnect the negative pole of the battery and only reconnect after the installation is complete)
FUNCTION WIRE COLOUR
Earth ðð BLACK initialled “M”
Battery positive ðð BLACK initialled “R”
Ignition live ðð YELLOW
Direction indicator lights ðð 2 x ORANGE
Door pin switch ðð GREEN-BROWN
Boot and bonnet switch ðð GREEN
Positive alarm armed ðð PINK
Sensors inlet ðð GREEN-BLACK
Outlet negative control for
additional siren
ðð YELLOW-BLACK
Central door locking ðð YELLOW-RED, YELLOW-GREY, RED-GREY
NOTE: in the wiring harness there are 2 connectors; connect the 4-pin connector to the
ultrasonic module and the 2 -pin connector to the LED.
WORKING DESCRIPTION
ALARM ARMING
Press on the transmitter 1 button. The arming is signalled by 1 direction indicator lights flashing
and one acoustic signal (can be excluded).
ALARM DISARMING
Press on the transmitter 1 button. The disarming is signalled by 3 direction indicator lights flashing
and 3 acoustic signalling (can be excluded); 5 direction indicator lights flashing and 5 audible tones
(can be excluded) if an alarm condition has occurred.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7201 in the language / languages: English as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info